[Amps] 1296MHz amp kits available

[Rod Adkins]

A kit to produce 30W at 1296MHz has been engineered by members of the San Bernardino Microwave Society http://www.ham-radio.com/sbms/  and the San Diego Microwave Group http://ourworld.compuserve.com/homepages/edmunn/  :
    - power gain 10 - 13dB (so budget for 3W i/p) - uses a PTF 10021 FET
    - 28v dc supply; current drain about 2A (or use 24v & lose <1dB power o/p)
    - cost $45 + $5 s&h (shipping USA; kit does not include heatsink, connectors or T/R relay)

For full details, assembly & test info, and to order a kit, email 1296amp at cox.net
Note: this kit contains surface mount components; familiarity with handling these is helpful (BUT: it just ain't that hard - see comments below)

For pic of completed amp, see http://kahuna.sdsu.edu/~mechtron/hamshack/1296Amp/1296Photo1a.jpg (note: you do not have to erode the heatsink as much as our brave beta-tester did <g>)

Personal comments from a builder:
    - I have successfully completed one kit, with a second on the way; splitters/combiners also under construction
    - I used a Model 99 heatsink from Communications Concepts ($22 + s&h) http://www.communication-concepts.com/heat_sink.htm
    - to accomodate the FET height vs PCB thickness, I chose to use a sheet of 0.032 in thick brass beneath the PCB instead of washers or bending the FET tabs; I used item #253 from K&S Engineering www.ksmetals.com. Many hobby stores have a display area with K&S products.
    - I decided to use a 4in x 6in slab of copper between the FET and the aluminum heatsink to better distribute heat. I bought mine from Industrial Metal Supply Co., who sell metal offcuts by the lb http://www.imsmetals.com/ locations Irvine, Riverside, San Diego & Sun Valley in CA
    - thermal grease: to use or not to use? There are many opinions. Advice I have had is that use of grease prevents getting a good rf ground - leads to possible oscillation & thermal runaway. 
    - I found the bias adjustment pot somewhat fragile, so, being ham-handed (sorry!), I am using a 10-turn encapsulated pot in my Mark II version
    - the clearance holes in the PCB are large enough to permit the use of #6 machine screws (NOTE: must use #4 for mounting FET); having broken a #4 tap recently, which stuck in the project... need I say more
    - power relays; for brick amps,I have standardised on an NTE SPDT, 12v coil, 40A contacts, encapsulated relay from Mouser http://www.mouser.com ; $7.25 ea @5-off; part # 526-R51-5D40-12F. Spade terminals and easy mounting with a #10 screw.
    - rf relays; I use Transco SPDT, SMA relays from DEM http://www.downeastmicrowave.com/ $45ea guaranteed working; I have been told they will tolerate 80W COLD-switched at 1296. They are nom 28v, but DEM sells neat kits for operating from 12v (which I use)
    - connectors; I used right-angle SMA, PCB-style; I found I needed to file the pins slightly to achieve a sliding fit; pyrojoe claims SMA is good to 400W, so have at it...
    - surface mount parts; I use demagnetized tweezers & a fine Weller soldering iron bit; if, like me, you suffer from the "slippery little suckers" syndrome, a la "Pretty Woman," spread a sheet on the floor & work directly on it. Sounds daft. Wait 'til you're searching for an SMD cap on your workshop floor...

Now make some noise on the 1296 nets:
    - WSWSS http://www.wswss.org/  Tues & Fri evenings
    - PNWVHFS http://www.pnwvhfs.org/  Sun am

Any info on other reflectors you think this email should be listed on, please advise the writer off-list

Rod Adkins WI6M