[Amps] Fw: "Tubes 201" - How Vacuum Tubes Really Work

[Will Matney]

Peter,

Thanks for this. I know how hard it is after doing all the typing I've been doing over the past fiew days. Since that's all there is of concern, don't put yourself out on copying the pages. That's just more work.

Thanks again,

Will

*********** REPLY SEPARATOR  ***********

On 7/25/06 at 11:33 PM Peter Voelpel wrote:

>Hi Will and the group,
>
>OK, I will scan it as it is and load it up tomorrow.
>
>You will have a hard time to find the book, it is called bei Siemens
>"Sende- und Genaratorröhren Hochspannungsgleichrichter und Stromtore"
>My edition is from 1966.
>
>Here we are with the translation of the most important parts and my
>comments
>following |:   
>
>
>6. Safety measures
>
>For the use of transmitting tubes certain safety measures are necessary,
>which use is mandatory for warranty claims.
>They consist of automatically working safety- and trip devices which safe
>the tubes from destruction in case of failures.
>
>For the safety of the tube against arcing, beside over current trip of the
>HT supply, a means of fast cut off of the anode voltage is necessary, which
>provides a fast disconnect from the electrode voltages.
>By means of a simple test wire it has to be tested if the quick trip
>circuit
>fulfils the requirements of the fast disconnect of voltages.
>For this purpose a small copper wire, of the diameter given in the table,
>must be used to short the anode voltage right at the anode electrode.
>If the copper wire is not melted the circuit can be used. Also if the short
>is present while the anode voltage is switched back it must not melt.
>
>| for me it works very well with my YL 1056 amp (two tubes), the
>overcurrent
>sensor in turn fires the thyristors across the anode voltage without
>melting
>a 0,1mm test wire. 
>The 3-phase power supply is 4KV 4A CCS
>
>A few examples of the table:
>
>tube    copper wire diameter
>
>RS 1001    0,16mm
>RS 1032    0,13mm   
>RS 1052    0,13mm
>RS 2041    0,25mm
>
>| The RS2041 is a tetrode with 220KW of dissipation running 18KV 60A
>maximum!
>
>
>Beside that measure there has to be a safety resistor of 5 to 25 Ohms, to
>be
>installed into the B+ line from the HT supply, which absorbs in case of
>arcing the energy of the capacitor bank and by this means, the requirement
>of the quick disconnect for the test wire condition fulfils.
>The anode voltage may be switched in again after 100mS earliest.
>
>The grid circuit also requires safety measures to prevent consistent arcing
>in the tube, when a separate bias supply is used, after an arc was
>developed
>
>| I understand it as when the grid is not strapped to ground
>
>This measure works with an additional resistor of about 50kOhm which must
>be
>switched in with help of the anode over current relay.
>Additional safety is reached when this resistor can also be switched in by
>an over current relay in the grid circuit.
>
>Against thermal overload of the anode, when made for forced air cooling,
>tube fuses were developed which in conjunction with a pull switch cut off
>anode and heater supply voltage.
>
>| I am using such a fuse on my YL1050, it is screwed into the anode cooler
>and holds through some litz wire the pull switch closed, when the
>temperature rises above the critical temperature, the wire is released from
>the switch in the tube cooler and the pull switch opens and interrupts the
>voltage to the mains relay coils of the transformers.
> 
>73
>Peter
>
>
>
>
>-----Original Message-----
>From: amps-bounces at contesting.com [mailto:amps-bounces at contesting.com] On
>Behalf Of Will Matney
>
>Peter,
>
>That's ok. I wouldn't want to ask you to translate it as that would be too
>big of a job. I wish they had an English version, I'd buy it if I could
>find
>it for the info.
>
>
>_______________________________________________
>Amps mailing list
>Amps at contesting.com
>http://lists.contesting.com/mailman/listinfo/amps