[Amps] premade HV rectifier board

[Jim W7RY]

Why would you fry the filament by turning up the plate voltage? The plate 
transformer and filament transformer are separate.

Jim W7RY


-----Original Message----- 
From: Carl
Sent: Thursday, July 04, 2013 6:21 PM
To: Jim W7RY ; Alek Petkovic ; Dave Hachadorian
Cc: amps at contesting.com
Subject: Re: [Amps] premade HV rectifier board


>I put a WD7S power supply board into my AL-82. Works perfectly. It has 10
> caps on it. It also fits perfectly into the AL-82, AL-1200 and AL-1500.
>
> You could probably even put the transformer on the "high tap" if you 
> wanted to.
>
> 73
> Jim W7RY
>

And fry the filament faster....

Carl
KM1H
>
> -----Original Message----- 
> From: Alek Petkovic
> Sent: Thursday, July 04, 2013 4:18 PM
> To: Dave Hachadorian
> Cc: amps at contesting.com
> Subject: Re: [Amps] premade HV rectifier board
>
>
>
> On 5/07/2013 6:25 AM, Dave Hachadorian wrote:
>> A friend of mine blew one of the filter capacitors in his
>> AL-1500.
> Yeah and I know why. There are 8 x 450V rated capacitors giving a total
> working voltage of 3600V, in that bank. The plate voltage in that amp
> is, at most times, higher than that. Up to 300V higher.
>
> A pretty marginal design, to say the least.
>
> I replaced all 8 caps in my amp, to 500V rated units and added a few
> more microfarads in the process. I now have a bit of headroom in the
> voltage department and a bit better dynamic regulation, resulting in
> more Watts out for the same amount of drive. So far, so good.
>
> 73, Alek. VK6APK
>
>
>
>
>> As I remember, the entire filter capacitor board, with
>> capacitors and resistors installed, was very reasonably priced.
>> ($180?)  I suspect that their Rectifier Board is also reasonable.
>> The techs at Ameritron are very friendly, knowledgeable, and a
>> pleasure to deal with.
>>
>> The AL-1500 manual, with schematic, is here:
>> http://www.qsl.net/4/4x6on/RADIO%20MANUALS/AMERITRON/AMERITRON--AL-1500-User-Manual.pdf
>>
>>
>> Dave Hachadorian, K6LL
>> Big Bear Lake, CA
>>
>>
>> -----Original Message-----
>> From: Stein-Roar Brobakken[LA6FJA]
>> Sent: Thursday, July 04, 2013 5:31 AM
>> To: amps at contesting.com
>> Subject: [Amps] premade HV rectifier board
>>
>>
>> Hi
>>
>> Does anyone know a place to buy premade HV rectifier board etc
>> for HF
>> amplifier?
>>
>> 73s LA6FJA Rag
>>
>>
>>
>>
>>
>> _______________________________________________
>> Amps mailing list
>> Amps at contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>> _______________________________________________
>> Amps mailing list
>> Amps at contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>>
>
> -- 
> From sunny Binningup, Western Australia.
>
> Family Businesses:
> Petkovic Air&  Gas. petkovicag at bigpond.com
> SP Electrical. www.spelectrical.net.au
> Hampers by Hand. www.facebook.com/hampersbyhand
>
> http://www.qrz.com/db/vk6apk
> http://www.qrz.com/db/vk6ap
>
> _______________________________________________
> Amps mailing list
> Amps at contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
> _______________________________________________
> Amps mailing list
> Amps at contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1432 / Virus Database: 3204/5964 - Release Date: 07/04/13
>