[Amps] SB-220 6M conversion
Artek Manuals
Manuals at ArtekManuals.com
Sat Jun 6 06:31:29 EDT 2020
Roger
1)See Item #3 in original post !!
2) 3KV under load ???
3) What are you using to measure power out ?
4)What did you use the to measure the plate voltage? The meter on SB220
or some other source?
Dave
NR1DX
On 6/6/2020 1:28 AM, Roger - W7TZ wrote:
> My recently purchased conversion has a tuned input where the band
> selector was. 3kv plates, 50w input gets me ~1kw out.
>
> 73, Roger
> W7TZ
> CN83ia
>
>
> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
> Virus-free. www.avg.com
> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
>
>
>
> On Fri, Jun 5, 2020 at 8:47 PM Artek Manuals <Manuals at artekmanuals.com
> <mailto:Manuals at artekmanuals.com>> wrote:
>
> Agree in principle..QSK on 6M not that important
>
> Dave
> NR1DX
>
> On 6/5/2020 11:30 PM, Jim wrote:
> > Good article except for tearing out the original relay. Not
> necessary,
> > unless you want to use QSK or hate the sound of loud relays
> (like I do).
> >
> >
> > Thanks
> > 73
> > Jim W7RY
> >
> > On 6/5/2020 10:24 PM, Adrian wrote:
> >> Have you seen this one Steve ?� ;
> >>
> >> http://www.arrl.org/files/file/Technology/QST_Apr_2008_p38-40.pdf
> >>
> >>
> >> On 6/6/20 1:10 pm, Artek Manuals wrote:
> >>> I have enough HF amps here (four at last count) One of them is an
> >>> ancient SB-220 , so I thought what the heck I would "hack" it and
> >>> turn it into a 6M single band. I have a folder� full of
> articles on
> >>> how to from the last 20 + years.
> >>>
> >>> All done "physically" but try as I may I can not get more than
> about
> >>> 600w out .
> >>>
> >>> 1) Two different tank circuits , one with a section of the
> original
> >>> 10/15� coil from the SB220 and a 2nd one with a a piece of flat
> >>> copper strap ...no difference
> >>> 2) Changed the parasitic chokes
> >>> 3) Tried� "T" input match. Pi input match , straight through
> ...no
> >>> difference
> >>> 4) Plate voltage is 2400 unloaded and about 2050 loaded in CW
> position
> >>> 5) Bias measures 6V
> >>> 7) Has new Hardbach bias and diode and metering board
> >>> 8) Older set of Eimac 3-500Z and newer set RF Parts 3-300ZG ...no
> >>> difference
> >>>
> >>>
> >>> What am I missing, ?
> >>> What else to try?
> >>>
> >>> Dave
> >>> NR1DX
> >>> manuals at artekmanuals.com <mailto:manuals at artekmanuals.com>
> >>>
> >> _______________________________________________
> >> Amps mailing list
> >> Amps at contesting.com <mailto:Amps at contesting.com>
> >> http://lists.contesting.com/mailman/listinfo/amps
> >
> > _______________________________________________
> > Amps mailing list
> > Amps at contesting.com <mailto:Amps at contesting.com>
> > http://lists.contesting.com/mailman/listinfo/amps
>
> --
> Dave
> Manuals at ArtekManuals.com
> www.ArtekManuals.com <http://www.ArtekManuals.com>
>
>
> --
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
>
> _______________________________________________
> Amps mailing list
> Amps at contesting.com <mailto:Amps at contesting.com>
> http://lists.contesting.com/mailman/listinfo/amps
>
--
Dave
Manuals at ArtekManuals.com
www.ArtekManuals.com
More information about the Amps
mailing list