[ct-user] CW, CT and the FT1000MP

[Jim Brannigan]

In Real Estate it's Location, location, location
In Ham Radio it's RFI, RFI, RFI.........
There is no simple solution.
Unplug EVERYTHING and start adding cables until the problem(s) are found.  A
large box of ferrite clamp-ons will be helpful.

I thought I had licked the latest RFI-in-the-computer issue until the wee
hours of Saturday night.
I was rolling along on 80M (KW) until I hit just the right frequency, then
locked keyboard, key down!!!
over the years I have learned to send with a paddle in one hand and type
with the other hand....

Good Luck
Jim


> I have an equipment problem that is driving me nuts...This reflector
> seemed appropriate as another CT User might have experienced the same
> thing...
>
> My station, in part, consists of a FT1000MP, interfaced with my computer
>
> via the serial port (COM1) for rig control, and via LPT1 for the CW
> interface...Have old Heathkit external keyer and Bencher paddles going
> to the second paddle input on the 1000MP...I use CT as my contesting
> software...
>
> My problem...When using CT to send CW, I am limited to VERY low power or
>
> my 1000mp TX keys and locks on...The only way to unkey the rig is to
> turn the RF OUT knob way down...(I'm talking about 10 or 15 watts on 15
> metres, ugggggg!!)...The only band that seems unaffected is 10 metres,
> where I can crank the amp to full power with no problems...
>
> Simple problem of RF getting into the cabling between the rig and
> computer, right ? That's what I thought too...After replacing all
> cabling with shielded cabling etc etc, the problem is still
> there...Here's the quirk...I can use other programs (LOG-EQF for
> example) to send CW via the keyboard and same computer-to-rig
> interfacing with no problems...Full power on all bands works OK...
>
> In addition, the lock-on problem only happens after I first use CT to
> send CW...Here's a typical scenario that I tested a dozen times last
> night to be sure it wasn't intermittent...
>
> -Turn rig ON with computer OFF...All OK...Can send CW with paddles at
> full power...
> -Turn computer ON without CT running, all OK...Can use full power with
> paddles, and LOG-EQF will send via the keyborad OK at full power...
> -Start CT, use paddles to send CW, all OK...Hit F4 on keyboard to send
> my call, and the TX keys and locks until I turn RF OUT down to minimal
> level...Now, even using the external paddles will lock the TX on...
> -Close CT, paddles still lock TX on...
> -Open LOG-EQF, can now use either the paddles or keyboard to send CW...
>
> BOTTON LINE...Can't use CT to send CW via the keyboard at any more than
> 15 watts!! (made for fun last weekend I'll tell you!!...Wife's dream
> almost came true, she thought I was going to turf everything out the
> basement window Saturday afternoon)...
>
> What am I missing here ? I realize that it is an RF problem, but why
> only when running CT ? If it happened when I was using other programs to
>
> send CW, I could understand...Is there something in CT that I have set
> wrong ? (I do NOT use CT for rig control, therefore no COM port settings
>
> are used in CT SETUP)...OR...Is there a menu setting in the FT1000MP
> that could be fouling things up ?...The ONLY time this problem arises is
>
> when I start CT...( No slight against the program, it likely isn't even
> the program's fault)
>
> Again, I have used shielded cabling and tried torroids everywhere etc
> etc etc...
>
> Any help would be GREATLY appreciated...It's baffling me...Maybe
> something to do with using the LPT port for CW keying with CT ? Can I
> use the COM port to key the FT1000MP from CT?
>
> 73, Scott VE1OP
>
>
>
>
>
> _______________________________________________
> ct-user mailing list
> ct-user@contesting.com
> ct-user-request@contesting.com Subject=unsubscribe to unsubscribe
> http://lists.contesting.com/mailman/listinfo/ct-user