[Orion] Re: Orion - work in progress - Now RFI
Richard Detweiler
rdetweil at hotmail.com
Fri Dec 17 10:06:49 EST 2004
I have second floor station with HIGH power to a vertical, this can be very
difficult for RF Grounding. At first RFI and RF in the shack was terrible
at my QTH.
I would do these two things first,
1). Replace ALL and I mean ALL coax with the LMR-400. Make sure all
connectors are tight, check them a second time by hand and tighten them
again. This alone kicked the but out of most of my RFI problems.
LMR-400 sheild is superior and the losses at HF are very low, Remember,
there are 3 conductors on a coax. Cheaper coax (RG-8 & 213) will let the RF
from the Inner shield and conductor escape to the outer sheild. LMR-400 is
100% film sheilded with a second wire mesh sheild for a very secure
transmission line.
2). Use the Sheilded Ground talked about below. Use a Coax - LMR-400 is
better for this but RG-8 is ok - at the ground rod, connect both Sheild and
center conductor together. At the last item in your shack before it goes to
the antenna ( in my case this is the High Power RFI Low Pass Filter )
connect ONLY the center conductor. leave about an inch of the center
insulating material. Tape up the end to cover and insulate the sheild that
was exposed. Then connect every other RF ground to that point.
I have very very little RF on my cases now and thus have never had my Orion
do any thing weird becarse of RFI. No flickering on my monitors, nothing in
my mic, and nothing going funny in my house.
I would not be in a hurry to buy the line isolators and baluns, At high
power these tend to over heat, They are ok for Low power when the antenna
is at a good SWR.
Best 73's
Rich
K5SF
>From: N0KHQ at aol.com
>To: k3cc at fast.net, tentec at contesting.com, orion at contesting.com
>Subject: [Orion] Re: Orion - Work in Progress
>Date: Mon, 13 Dec 2004 11:26:47 EST
>
>Hi Skip,
>
>I understand you frustration with the Orion.
>My frustration with SDR's began with the purchase of the Jupiter about 3
>years ago.
>
>I know you probably don't want to hear this, but, these rigs are very
>susceptible to RFI. If there is any...and I mean any, stray RF in your
>shack the
>Orion or the Jupiter will find it.
>
>First off, the Orion, like the Jupiter, is nothing more than a computer in
>an RF environment inside a transceiver case.
>
>Special RF Grounding and Power Supply precautions must be taken in order
>for
>the Orion or Jupiter to perform without incident. I know what your going
>to
>say, "hey, I never had any problems with my other rigs". Well, your other
>rigs were not SDR's.
>
>A lot of hams have jumped into the SDR arena without thinking, like
>myself,
>about what they were getting themselves into. SDR's are the next step in
>the
>evolution of ham radio transceivers. By the peak of the next solar cycle
>you
>will see one of the other leading manufacturers of ham radio transceivers
>come out with an SDR. It could be Icom, they are in the early stages with
>the
>introduction of the IC-7800.
>
>All of the top rigs out today, TS-870, TS-950SDX, FT9000DX, IC-7800 and so
>on will be referred to as "Boat Anchors", just like we refer to the tube
>type
>rigs of yesterday as "Boat Anchors". I know all of these rigs work great,
>but
>there is a time when a product must evolve to the next step. And, SDR's
>are
>the next evolutionary step in Amateur Radio. Whether you, I, or anyone
>else
>likes it or not......its coming.
>
>If your dead set on getting rid of the Orion, don't waste your time reading
>any further. However, if your willing to give it one more shot......keep
>reading.
>
>Firstly, when you hear or read about an Orion owner praising the operation
>of their rig, they are not trying to blow smoke up your butt. It's true,
>the
>Orion is a great rig, and in my opinion, the best rig on the market today
>in
>any price range.
>
>So, here we go! Please follow these instruction exactly.
>
>1. If your running a balanced antenna, purchase a 1:1 50ohm Bal to 50ohm
>Unbal current balun from Radio Works (B1-2K) and install it at the antenna
>feed
>point. This balun will prevent antenna currents from coming down the shield
>of the coax and entering you station and at the same time allow for a
>graceful
>transition from a balanced system to an unbalanced system.
>
>2. If your running an unbalanced antenna, purchase an RF Balun kit from
>Polomar-Engineering and install it at the antenna feed point. For reasons
>above.
>
>3. Purchase from Radio Works a T-4 Line Isolator. This isolator will
>install
>right at the back of the coax connector/s on the Orion. This is a must do.
>
>4. The power for your Orion, I assume, is coming from a DC Power Supply
>that
>is plugged into a 115vac circuit. This circuit should be a dedicated
>circuit
>and not shared with other appliances in your home. Appliances in your
>home,
>depending on their load impedance's are dumping reactive currents onto
>your
>service neutrals and grounds. The currents are in the milliamp range and
>could
>create havoc in your power supply depending on how well your power supply
>is
>capable of filtering the incoming AC.
>
>5. What I do is, the DC power cable going from the power supply to the
>Orion
>is wrapped around a 2-1/2" toriod donut, 6 turns one direction and 6 turns
>the opposite and other direction.
>
>6. One of the biggest culprits is the Orion amplifier keying line. This
>line
>should be wrapped around one of those 3/4" x 3/4" x 1-1/4" toriod cubes as
>many times as possible. RS sells them.
>
>7. Now heres a subject that you may or may not have a problem with: RF
>Grounding.
>
>Some hams get a little confused when talking about Grounding for RF and
>Grounding for Lightning protection. They are not the same and should be
>addressed
>separately. Grounding for Lightning protection will do very little for RF
>grounding. But Grounding for RF will help with Lightning protection.
>
>Most ham radio books illustrate a typical station grounding system, where
>you have this big copper plate or bar behind your station and every piece
>of
>your equipment is supposed to be grounded to this bar and then a wire runs
>from
>this bar outdoors to a grounding rod. This illustration is 100% totally
>wrong
> and does result in the biggest ground loop in the history of Amateur
>Radio.
>
>We are talking RF Grounding here and only RF Grounding:
>Heres what you do. There should be only one point of connection for that
>wire running outdoors and that is at the wing nut on the back of your
>antenna
>tuner. If you have multiple station grounds disconnect them and thrown
>them
>away.
>
> >From Ten-Tec purchase a TT-1251 RF Counterpoise Tuner, it comes in kit
>form
>and will require assembly. I chose the 1251 over the MFJ because the 1251
>has
>more inductance available.
>
> >From the wing nut on the back of the antenna tuner run a short piece of
>copper coated metal plumbers tape (its available from Lowes) to the input
>of the
>1251, from the output of the 1251 run a piece of RG-8 coax, only the center
>conductor of the RG-8 will connect to the 1251 the shield will be removed.
>
>Outdoors, at the other end of the RG-8 connect the center conductor and
>sheild together.
>
>This is where you've got to trust me; depending on which frequency you are
>having problems with will determine how long you will cut the countrpoise
>wire/s.
>
>Lets say that the transmit operation of the Orion gets squirrely on 40 m.
>Cut a piece of 14ga stranded insulated wire 20' long (.15 wave length)
>connect
>one end of this wire to the shorted end of the RG-8, on the other end of
>the
>14ga wire solder the wire to a 2' piece of 1/2" copper tubing, stretch the
>wire out and pound the copper tube into the ground below grass level.
>
>Go back in the house, tune up the antenna tuner for operation on 40m, when
>the SWR is as low as you can get it, then move to the TT-1251. First, turn
>the
>1251 inductor knob for maximum meter reading, then turn the cap knob for
>maximum meter reading, then go back to the inductor knob and turn for
>maximum
>meter reading. The 1251 is simply an antenna tuner for your radial system.
>What
>you have done here is to resonate the other half of the antenna for
>operation
>on the exact frequency that your operating on.
>
>Using this system and the above suggestions, I can guarantee you that there
>will be no stray RF in your shack to interfere with the operation of the
>Orion.
>
>The guys on the reflectors wont see this but:
>
>I am attaching construction details on the RF Tunable Buried Radial System
>I
>run here at the QTH. Other Ten-Tec Orion and Jupiter owners have install
>this
> system and are very happy with the results. This information is provided
>to
>you for your use. If I didn't have this system installed at my QTH, there
>is
>no way I could try to run the Orion......been there....done that.
>
>In my opinion there are 5 issues that require correcting with the Orion:
>1. Monitor Level to low when listening to you transmitted audio.
>2. Sweep Display to slow
>3. Sweep Display intermittently freezes when in "Sub RX" and you push the
>"Sub RX" "NR" or "AN" buttons. This is corrected by rebooting the Orion.
>4. The "BW" issue when in CW and tuning from 1000hz to 100hz.
>5. "Sub RX" RF Gain quits working below a setting of 32.
>
>Last but not least, documentation and updating of the owners operations
>manual.
>
>Ten-Tec has come a long way since the introduction of the Orion a couple of
>years ago. You have got to admire the gutsiness of a small group of folks
>that
> live in the Smokey Mountains willing to risk it all. I support their
>efforts
>as I'm sure others do in there willingness to take the next step in the
>evolution of ham radio transceivers.
>
>I'm posting this information on both reflectors also, I get tired of typing
>rather quickly.
>
>Have fun.........and.........dont give up.
>
>Happy Holidays
>
>
>73
>John / N0KHQ / St. Louis
>
>Always on 18.130
>
>Antennas:
>
>You can build 'em better than you can buy 'em
>Please visit the sites below:
>_http://www.hamuniverse.com/antennas.html_ (http://www.hamuniverse.com/)
>_http://www.cebik.com/n0khq.html_ (http://cebik.com/nokhq/html)
>
>
>
>
>
>_______________________________________________
>Orion mailing list
>Orion at contesting.com
>http://lists.contesting.com/mailman/listinfo/orion
More information about the Orion
mailing list