[RFI] RFI, Power Company.

[Pete Smith N4ZR]

OK, that makes sense to me.  I have the good fortune to have become 
friends with the guy responsible for RFI at our local power company, so 
I have his direct line and can call him whenever I need help.  I think a 
large part of his cooperative attitude is that I locate the sources of 
my noise within a pole or two *before* I call.

73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.

On 5/28/2013 12:12 PM, EDWARDS, EDDIE J wrote:
> Very true Pete!  If a ham knows it is arcing, call it in as arcing!  But most hams do not go out and locate the source of their noise.  They just call it in.  If you call RFI in as arcing and it isn't, then the line tech who responded has to forward the trouble call on to the RI locator technician (if they have one).  This is especially true if they are unionized.
>
> I still suggest it's better to call in radio interference as radio interference so the first response is from the right technician to do the job.  If the source is actually arcing on the next block or neighborhood, then it'll probably get called in by someone on the block who is hearing or seeing it.
>
> >From Loftness' book in the Glossary:
> Sparking: (same as microsparking).  A complete electrical breakdown of air (or other gas), which generates EMI from below 1 MHz to above 1000 MHz and is the cause of most RI and TVI originating on power lines.  Usually is a small arc in a small gap (0.1" or less).  Does not maintain an ionized conductive channel between half-cycles of voltage wave as do power arcs.
>
> He didn't list power arcs in the glossary aside from this mention of it.
>
> My recommendation:
> Power Arcs:  Call it in as arcing immediately.
> RFI:  Call it in as RFI to schedule a visit.
>
> You guys might enjoy these arc videos if you haven't seen them:
> http://www.youtube.com/watch?v=PBfT9BARG3w
> http://www.youtube.com/watch?feature=endscreen&v=C-UTYzfNjKM&NR=1
> http://www.youtube.com/watch?NR=1&v=_FsRZ-I9_F0&feature=endscreen
>
> 73, de ed -K0iL
>
> -----Original Message-----
> From: RFI [mailto:rfi-bounces at contesting.com] On Behalf Of Pete Smith N4ZR
> Sent: Monday, May 27, 2013 4:03 PM
> To: rfi at contesting.com
> Subject: Re: [RFI] RFI, Power Company.
>
> I have Marv Loftness'sAC Power Interference Manual  Manual, and it makes
> it clear that sparking can cause RFI, as can arcing. He gives as an
> example of sparking loose hardware tying an insulator to a crossbar.
> The worst RFI I ever had resulted when a woodpecker undermined one of
> two lag bolts holding a lightning arrestor to a pole, causing sparking
> between the bracket and the loose bolt.
>
> 73, Pete N4ZR
> Check out the Reverse Beacon Network at
> http://reversebeacon.net,
> blog at reversebeacon.blogspot.com.
> For spots, please go to your favorite
> ARC V6 or VE7CC DX cluster node.
>
> On 5/27/2013 4:53 PM, Ed K0iL wrote:
>>     "AC Power Interference Handbook" [
>> http://www.arrl.org/shop/AC-Power-Interference-Handbook  ] also uses similar
>> language.   The ARRL RFI Book says "A sustained spark is often called an
>> 'arc'."  Then they also refer to power line RFI as "spark-type"
>> interference.
> _______________________________________________
> RFI mailing list
> RFI at contesting.com<mailto:RFI at contesting.com>
> http://lists.contesting.com/mailman/listinfo/rfi
>
> ----------------------------------------------------------------------
> This e-mail contains Omaha Public Power District's confidential and proprietary information and is for use only by the intended recipient.  Unless explicitly stated otherwise, this e-mail is not a contract offer, amendment, or acceptance.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.
>