[SCCC] Elecraft K3 - more impressions by N6TR

[Dennis Vernacchia]

 Just got this off the CQ-Contest Reflector.

This is a very promising radio that looks like it will give the
Japanese big 3 a run for the money and for a lot less
money than an IC-7800 or FT-9000

I am waiting a while til any bugs ( if any ) are worked out or other
features and software are changed/added/improved etc.
before purchasing one.

N6TR who has one of the first K3s, is a very prolific contest operator.

73, Dennis N6KI

---------- Forwarded message ----------
From: Tree <tree at kkn.net>
Date: Jul 23, 2007 12:26 PM
Subject: [CQ-Contest] Elecraft K3 - more impressions
To: cq-contest at contesting.com


Made it back from KL7 over the weekend.  I took my beta test K3 with me
and we did a multi-single from KL3R in the IARU contest (with K6AW and
KL7RA).

This 8 pound box sure packs in a lot of performance.  One option we
suggested
to Elecraft is a set of covers made out of lead - just to make it feel like
it has more stuff in it.

If you take off the top cover - the initial response is something like
"where
is the radio?".  It turns out most of the radio is comprised of surface
mount components on the bottom side of the main PC board.

For those of you who have read their brochure, you know that the first IF
is 8.2 MHz and this is where your "roofing filter" is.  I have two in my
radio currently - 400 hz and 2.8 khz.  There is room for five of them.
You can either switch between the filters and have the DSP match the
roofing filter - or continuously vary the bandwidth and have the roofing
filters automatically switch to the smallest filter that can be used to
support the desired bandwidth.  The combination of the roofing filter
and DSP results in a receiver that will hold its own in any situation I
can imagine.

The receiver sounds great and is a joy to use on SSB or CW.  It even did
well decoding RTTY signals directly to the diplay during the recent NAQP
RTTY contest.  Too bad the firmware isn't all done yet - or I could have
made some QSOs by sending information with my paddle and have the radio
send it out in RTTY or PSK.

On SSB - the transmit audio sounds very clean and I have gotten good
reports on the air (including a rag chew with KC7V on six meters).

The flexbility of the hardware is mainly determined by the firmware.
Elecraft has obviously packed plenty of power into the processor that
executes the firmware as the controls are all very responsive.  I was
impressed to find out that the squlech knob can be used for the RF gain
of the second receiver if installed.  The second receiver is an exact
copy of the main receiver (again with up to 5 filters) and will enable
diversity reception amongst other things.

The transmitter puts out 120 watts - so you have a bit of extra drive
power for your pair of 3-500Zs.  :-)

The operating controls are easy to use.  It didn't take me long to become
"at one" with the radio.  The VFO dial can be setup for 8 khz per rotation,
which is responsive enough for those fast sprint QSYs.  This is with 20 hz
resolution - so you don't hear the frequency steps (which I consider to be
very hard to listen to).

And the radio didn't turn into a pile of parts after about 7K miles on the
tough KL7/VY1/VE7 roads.  :-)

I understand Elecraft is close to publishing their performance
numbers.  They
want to make sure they have enough data from several units before doing this
and they tend to put some safety margin into them.  I understand they will
give even the $10K radios a run for their money - and probably finish ahead
in many areas.

I am not a numbers expert and go more by the sound of the radio - and this
one sounds great.

Elecraft is hard at work finishing up the firmware.  Some of the
functionality is new as of a few days ago and we are getting constant
updates to fix bugs and add new features.

73 Tree N6TR
tree at kkn.net
_______________________________________________
CQ-Contest mailing list
CQ-Contest at contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest