[Skimmertalk] [FlexEdge] PowerSDR and CW Skimmer not aligned

[Edward H Russell]

Oops I had CWL set. When switched to CWU the 9600 synchronizes properly. 

Ed W2RF

-----Original Message-----
From: Flexedge [mailto:flexedge-bounces at flex-radio.biz] On Behalf Of Andrew
O'Brien
Sent: Saturday, May 11, 2013 8:36 PM
To: Neal Campbell
Cc: flexedge at flex-radio.biz; SkimmerTalk Reflector
Subject: Re: [FlexEdge] PowerSDR and CW Skimmer not aligned

I assume it is default, says... CW Pitch 600 (Hz)


On Sat, May 11, 2013 at 8:32 PM, Neal Campbell <nealk3nc at gmail.com> wrote:

> What cw tone are you using in PSDR?
> 73
> Neal Campbell
> Abroham Neal LLC
>
> HUGE DAYTON CELEBRATION SALE!!
> Time to get the guaranteed setup for your SDR!
> Now until end-May
>
>
>
> On Sat, May 11, 2013 at 8:04 PM, Andrew O'Brien <k3ukandy at gmail.com>wrote:
>
>> Returning to this topic after a week break to rest my brain.  I 
>> tampered with the "IF audio" setting in CW Skimmer.  After trial and 
>> error, I now have CW Skimmer and PowerSDR aligned , the IF Audio 
>> setting that works is
>> 4500 Hz instead of 9600 Hz.  I have no idea why, nor any idea what 
>> issues changing it will cause, but my skims are aligned now.
>> Andy K3UK
>>
>>
>> On Wed, Apr 24, 2013 at 9:49 PM, Andrew O'Brien <k3ukandy at gmail.com>
>> wrote:
>>
>> > I have got PowerSDR and CW Skimmer working together, the frequency 
>> > displayed in PowerSDR is the same frequency in the main
>> display
>> > of CW Skimmer.  However a CW signal nicely centered in PowerSDR 
>> > does not show in the CW Skimmer waterfall at all.  CW signal DO 
>> > show in Skimmer's waterfall,  but not ones heard in PowerSDR's 
>> > audio.  When CW Skimmer
>> lists
>> > a CQ call in Call List, it is about 20 Khz off from PowerSDR.  I 
>> > Googled this issue and found some folks with similar issues in 
>> > 2011.  VAC
>> settings
>> > were suspect at that time but I did not see a solution , some said 
>> > the issue went away when VAC was updated to a new version.  I am 
>> > using the latest version and have VAC set up identical to the Flex 
>> > Knowledge Base screenshots on using CW Skimmer.  I note with 
>> > interest the fact that CW Skimmer has a Frequency Calibration 
>> > option that is grayed out when I use PowerSDR.  .
>> >
>> > Anyone have an idea or two on where to start?
>> >
>> > Andy K3UK
>> >
>> _______________________________________________
>> Flexedge mailing list
>> Flexedge at flex-radio.biz
>> http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz
>> This is the FlexRadio Systems e-mail Reflector called FlexEdge.  It 
>> is used for posting topics related to SDR software innovation and 
>> other technical SDR topics.
>>
>
>
_______________________________________________
Flexedge mailing list
Flexedge at flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz
This is the FlexRadio Systems e-mail Reflector called FlexEdge.  It is used
for posting topics related to SDR software innovation and other technical
SDR topics.