[Skimmertalk] [HamSCI] Rev'd FLEX-6000 & QS1R skimming/recording guides

Pete Smith N4ZR pete.n4zr at gmail.com
Mon Aug 7 07:35:28 EDT 2017


On August 21, 2017, from 1400 to 2200Z, operators of RBN nodes will have 
a unique opportunity to contribute to scientific understanding of the 
ionosphere.  That time-frame straddles the period when the solar eclipse 
will be visible across North America, and is also when the Solar Eclipse 
QSO Party will be run.

The RBN's unique contribution, in North America but also worldwide, is 
to provide as many data points as possible during the 1400-2200Z 
period.  In order to do this, two departures from normal practice are 
needed:

1.  It is desirable for science to have much more frequent spots of 
stations active in the QSO Party than could be produced with the 
standard 10 minute respot interval. To this end, Alex has provided for 
adjustabilty in this respect in the current versions of CW Skimmer, CW 
Skimmer Server and RTTY Skimmer Server.  By adding a single line to the 
.ini file for your skimming software, you can adjust the respot interval 
anywhere from the original 10 minutes down to zero.  In the latter case, 
every repetition of a station's callsign will be reported (provided of 
course that the station includes CQ or TEST at least twice in each 
transmission).

2. The RBN archive is not the best source of the scientific data we hope 
to produce, because the timing is relatively imprecise (nearest 
minute).  So check your Skimmer computer for a file titled "spots.txt" , 
which will be found in C:\users\[your 
username]\Appdata\Roaming\Afreet\Products\Skimsrv.  The spots.txt file 
gives the time when a spot is actually made, to the nearest second. 
Regrettably, there is no comparable file in CW Skimmer. For Skimmer ops, 
your data are welcome too, even if still on a 10-minute scale - after 
all the eclipse period is hours long!

If you have been operating your node for a while, this file will be 
quite large - all that we need is 1400-2200Z on the 21st.  You can use a 
text editor to extract the part we need.  Then send it to ///*TBD/// * 
so the scientists can get to work.

HamSCI is also looking for recordings of digital I/Q data from Skimmer 
receivers made during the duration of the Solar Eclipse QSO Party. This 
will allow HamSCI to replay and analyze recordings from specific 
receivers in greater depth following the contest. HamSCI will be 
publishing guides shortly on how this can be done with the QS1R or Red 
Pitaya and CW Skimmer Server, or with any SDR capable of sending data to 
CW Skimmer using its built-in recording function. Note that this will 
consume significant hard disk space - up to about 4GB per hour per band. 
The data will be accepted for upload after the contest.

If you're interested in putting your node to work on this project, 
you're still lacking one thing - the magic formula to put into your 
Skimsrv's ini file. *Email me*, and the secrets of the universe will be 
revealed.

I'm doing it this way because I want to have some reasonable confidence 
that people won't start using shorter interval settings with the RBN 
servers outside the eclipse period.  Even one Skimmer can make a big 
difference in this regard, and *we will not hesitate to block anyone's 
spots from the RBN server if they violate this rule outside the eclipse 
period.*

73, Pete N4ZR
Check out the Reverse Beacon Network
at<http://reversebeacon.net>, now
spotting RTTY activity worldwide.
For spots, please use your favorite
"retail" DX cluster.

73, Pete N4ZR
Download the new N1MM Logger+ at
<http://N1MM.hamdocs.com>. Check
out the Reverse Beacon Network at
<http://reversebeacon.net>, now
spotting RTTY activity worldwide.
For spots, please use your favorite
"retail" DX cluster.

On 8/6/2017 1:20 PM, Sam Rose wrote:
> Hi everyone,
>
> This weekend I attempted to finalize the FLEX-6000 skimming/recording 
> guide, and with the help of Alex, W2AXR, wrote one for the QS1R. With 
> the QS1R, it's actually quite easy to skim and record seven 
> 192KHz-wide slices of RF.
>
> I'm handing these off for review of those of y'all interested in doing 
> so - otherwise, I think it's time to publish and promote, as users 
> still have a couple weeks to get things set up.
>
> This leads me to two questions as well...
>
> 1. Have we created much buzz among the Skimmer community, ie on the 
> skimmertalk message board? Alex is a member of this and he's said that 
> he has seen very little here about the Solar Eclipse QSO Party, and 
> nothing he recalls about configuring RBN nodes to do I/Q recording as 
> well.
>
> 2. Do we have a similar guide for the Red Pitaya? I looked around the 
> HamSCI site, and the available documentation seems very disjoint to me 
> - there's the "main" guide on how to set up an RBN node with a Red 
> Pitaya, but this doesn't mention anything about recording - it uses 
> the non-CWSL_Tee method. Then there's N6TV's guide which does use this 
> method, but doesn't mention how to run any recorder - the page that 
> links to this guide only mentions that it's possible. And the MIT 
> Haystack Github pages provide little in the way of obvious instruction 
> on how to get things running - unless you really have to go through 
> all of that compiling every time, yikes!! It's quite easy to get lost 
> in what's there now, which, with two weeks to go, is not a situation I 
> like.
>
> I think we need one "central" guide for the Red Pitaya - in my 
> opinion, what's posted in public now is not adequately intuitive for 
> the intelligent non-engineer to set up a combined recording/skimming 
> node - and if we want a lot of recordings to come back, we need 
> something better. Perhaps we modify the main guide to use the CWSL_Tee 
> method, and instruct users to connect CWSL_File (or the new MIT 
> utility if this can be done - and heck, if that'd work with the QS1R 
> then I could modify that guide to call for that also) and consolidate 
> it all into one intuitive guide.
>
> 73 -
> Sam, KC2LRC
> -- 
> You received this message because you are subscribed to the Google 
> Groups "HamSCI" group.
> To unsubscribe from this group and stop receiving emails from it, send 
> an email to hamsci+unsubscribe at googlegroups.com 
> <mailto:hamsci+unsubscribe at googlegroups.com>.
> To post to this group, send email to hamsci at googlegroups.com 
> <mailto:hamsci at googlegroups.com>.
> Visit this group at https://groups.google.com/group/hamsci.
> To view this discussion on the web visit 
> https://groups.google.com/d/msgid/hamsci/CA%2ButXW-VFv13%3DjxuToCw2HdEGAfu2CmKRpMR_bqC%3D%3DqQmWNJJg%40mail.gmail.com 
> <https://groups.google.com/d/msgid/hamsci/CA%2ButXW-VFv13%3DjxuToCw2HdEGAfu2CmKRpMR_bqC%3D%3DqQmWNJJg%40mail.gmail.com?utm_medium=email&utm_source=footer>.
> For more options, visit https://groups.google.com/d/optout.



More information about the Skimmertalk mailing list