Hi.
I have a Flex5000 set up
with CWSkimmer. Both CWS and RigSync are following the
Flex frequency exactly as it should, hence CAT
communication is OK. This is also indicated on the bottom
of the CWS screen.
I am unable to get any
decoding on the screen.
I have uninstalled and
reinstalled everything about 4/5 times. Followed the CWS
and RigSync guide lines to the letter, used the knowledge
base for Flex, but no written decoding.
Looking to the bottom of
the CWS screen everything seems to work, but nothing on
the right window of CWS. The CW signals seem also very
faint, like there is insufficient signal strength for CWS
te decode.
The waterfall is going,
but no decoding, while on the bottom of the CWS screen the
following is shown:
CAT
interface OK
Audio
input bandwidth OK
Decoder
capacity used: 16%
Decoders:
39 of 39
SNR:
-2dB
23WPM
Tln:
1 user
Can somebody help me
please.
Thanks.
Best 73s de,
Eb W. ZL4RM/PA0JAG
Sounds like you have selected 3 kHz audio mode as
the radio model in CW Skimmer. Probably not what was
intended. With that option, you would have to feed the audio
output of the Flex (the headphone jack) to the sound card
input.
Looks like you need a 3rd party program for full band
skimming (SDR Bridge or SliceMaster). I don't know anything
about them.
Hi.
I have a Flex5000
set up with CWSkimmer. Both CWS and RigSync are
following the Flex frequency exactly as it should,
hence CAT communication is OK. This is also
indicated on the bottom of the CWS screen.
I am unable to get
any decoding on the screen.
I have uninstalled
and reinstalled everything about 4/5 times. Followed
the CWS and RigSync guide lines to the letter, used
the knowledge base for Flex, but no written
decoding.
Looking to the
bottom of the CWS screen everything seems to work,
but nothing on the right window of CWS. The CW
signals seem also very faint, like there is
insufficient signal strength for CWS te decode.
The waterfall is
going, but no decoding, while on the bottom of the
CWS screen the following is shown:
CAT interface OK
Audio input bandwidth
OK
Decoder capacity
used: 16%
Decoders: 39 of 39
SNR: -2dB
23WPM
Tln: 1 user
Can somebody help me
please.
Thanks.
Best 73s de,
Eb W. ZL4RM/PA0JAG
_______________________________________________
Skimmertalk mailing list
Skimmertalk@contesting.com
http://lists.contesting.com/mailman/listinfo/skimmertalk
SDR-Bridge (me) and
Slice Master (K1DBO) are for Flex 6000 series. RigSync
(me) is for Flex 5000 series and works with many other
radios.
It seems like your
setup is good and RigSync is working properly. Send me a
screen shot of CW Skimmer and I’ll try to diagnose.
Tks,
73
Ed w2rf
Sounds like you have selected 3 kHz
audio mode as the radio model in CW Skimmer. Probably not
what was intended. With that option, you would have to
feed the audio output of the Flex (the headphone jack) to
the sound card input.
Looks like you need a 3rd party
program for full band skimming (SDR Bridge or
SliceMaster). I don't know anything about them.
Hi.
I have a Flex5000 set up
with CWSkimmer. Both CWS and RigSync are following
the Flex frequency exactly as it should, hence CAT
communication is OK. This is also indicated on the
bottom of the CWS screen.
I am unable to get any
decoding on the screen.
I have uninstalled and
reinstalled everything about 4/5 times. Followed
the CWS and RigSync guide lines to the letter,
used the knowledge base for Flex, but no written
decoding.
Looking to the bottom of
the CWS screen everything seems to work, but
nothing on the right window of CWS. The CW signals
seem also very faint, like there is insufficient
signal strength for CWS te decode.
The waterfall is going, but
no decoding, while on the bottom of the CWS screen
the following is shown:
CAT
interface OK
Audio
input bandwidth OK
Decoder
capacity used: 16%
Decoders:
39 of 39
SNR:
-2dB
23WPM
Tln:
1 user
Can somebody help me
please.
Thanks.
Best 73s de,
Eb W. ZL4RM/PA0JAG
_______________________________________________
Skimmertalk mailing list
Skimmertalk@contesting.com
http://lists.contesting.com/mailman/listinfo/skimmertalk