OK, but remember that the RP 14 and RP 16 can't use the same version of start.sh.

73,
Bob, N6TV

On Mon, Jun 3, 2024, 6:26 PM William Liporace <wc2l@wc2l.com> wrote:

OK,
I have absolutely NO idea what changed.. I'm on the spare. It is working perfectly. I just went through ALL of the files again. Cleaned up a few log files and now it is all up and running correctly. I want to revisit the old unit with a fresh SD card. As far as I remember, they were both setup by you. At the time, you couldn't run everything (CW, RTTY, Digital) on one device (If I remember).

I will look at setting up a spare PC and play around. Worst case, make a copy of the working SD card and go from there. I have not looked at updates or changes in long time. I think I have kept up with most of the software.

Will WC2L

On 6/2/2024 11:33 PM, Bob Wilson, N6TV wrote:
I forgot to ask, did you move SD cards between the two RPs? If not, does the new RP have a copy of apps/sdr_receiver_hpsdr_122_88/start.sh in the root folder to automatically start the SDR receiver app?

73,
Bob, N6TV
On Sun, Jun 2, 2024 at 8:31 PM Bob Wilson, N6TV <n6tv@arrl.net> wrote:
As I recall, you have a very complex network environment. The SkimmerPC and the Red Pitaya have to be on the same subnet of the same LAN or else HermesIntf_xxxx.dll will not be able to locate the RP via its MAC access.

xxxx must be the last 4 bytes of the new RP's MAC address. Do not change SkimSrv.ini.

After editing CWSL_Tee.cfg (must be done with Administrator privileges otherwise it gets saved in a "Virtualstore" folder that CWSL_Tee.dll will not find).

Finally, after editing CWSL_Tee.cfg, you have to copy it to the C:\RBN folder or wherever Aggreagtor.exe is stored.

73,
Bob, N6TV
On Sat, Jun 1, 2024 at 8:49 PM William Liporace <wc2l@wc2l.com> wrote:
OK, I guess I'm stumped..
My long time Red Pitaya is tossing errors.
SDR Failure:Timed out waiting for UDP data
Error Access violation at 0x774854E5 (tried to write to 0x00000014), program terminated.

When I place my other Red Pitaya in the line.
If I remember correctly, I need to change
CWSL_Tee.cfg, Rename HermesIntf_xxxx.dll, modify SkimSrv.ini

I can SSL to the new address. it will bascially not run.
Seems like is has no idea where DeviceName=01 CWSL_Tee on RP-F07CD2 v25 is. (not sure v25 is needed)

SkimSrv in the receiver say it is 01 CWSL_Tee unknown

Ideas, what am I doing wrong? not what I expected.

Will WC2L
-- 
William Liporace WC2L
http://www.wc2l.com or http://dxc.wc2l.com
AR-Cluster Node  telnet dxc.wc2l.com 7373 or 144.93 MHz
wc2l@wc2l.com
_______________________________________________
Skimmertalk mailing list
Skimmertalk@contesting.com
http://lists.contesting.com/mailman/listinfo/skimmertalk
-- 
William Liporace WC2L
http://www.wc2l.com or http://dxc.wc2l.com
AR-Cluster Node  telnet dxc.wc2l.com 7373 or 144.93 MHz
wc2l@wc2l.com