[TenTec] Omni 6+ problem inquiry

Ken & Rose Kreis kia@netins.net
Sat, 13 Nov 1999 10:03:19 -0600


My Omni VI+ kc digit does not jump.

I use a dial speed of 1kc per rev.  On FM it does have a higher kc per rev.
(about 10kc) but I would think that is supposed to be on FM where the
bandwidth is wide.

The only problem I have is my own in forgetting to fully take off a towel I
use to cover up the rig. Keeping the vent holes covered while cw-ing for a
hour the rig starts to sound like a Scout QSYing all over the place.

Hope you find your problem.

73,

Ken Kreis, KA0W
P.O. Box 272
Rudd, IA 50471
E-mail: kia@netins.net





----- Original Message -----
From: <bhalterman@desupernet.net>
To: <tentec@contesting.com>
Sent: Saturday, November 13, 1999 8:53 AM
Subject: [TenTec] Omni 6+ problem inquiry


>
> I have a Omni 6+ that has rather annoying problem and I wonder if others
> might have noticed it too. The problem is not affecting the operation of
> the radio, it is Just DAMN annoying..... expecially with a price tag of
> 2600 bucks.
> When tuning the radio down in frequency (Turning the knob CCW) at a rate
> of about 2  revs per second, the KHZ digit will very quickly jump to
> another digit, then back again.
> You might see the digits change say from 8, 7, 6, 7, 6, 5, 4, 3, 2, 1,
> 2, 1, 0 etc.
> What acutally is happening is that the processor is causing the PLL to
> jump up in frequency by about 1Khz or so. The amount of jump is
> dependent upon the tuning rate settings. i.e., the slower the tuning
> rate the smaller the amount of jump.
> I have found that with a 5KHZ setting, the jump is about 1khz. This
> malady is not a function of the encoder as that would cause smaller,
> minute jumps.
> Another test that will mimick the above and skitz out the CPU big time,
> is to run the PLL to the LOWEST frequency it will tune (any band), go to
> the FM mode,  then turn the knob in the CCW direction at a rate of about
> 2-3 revs per second. If your radio is ok, you will not see anything
> happen. If your radio has this problem like mine, you will see the lower
> 4 digits quickly change to other digits. If you stop quick enough, you
> will notice the display is above where it should be. In other words, it
> jumped up in frequency.
> Another test is to zero the display to 7.000.00. with the finger index
> at a particular point, turn the knob in the cw direction 6-7 turns, note
> the frequecy you end up at. Then reverse direction and move the same
> amount of turns in the CCW direction. You should end up at the same
> frequency you started at (7.000.00) or very close to it.
>
> This radio has been back for repair twice. Each time it comes back not
> fixed. TT said they can not duplicate the problem, AND that all Omni 6's
> will do the same thing with the tuning knob test.
> Has anyone else experieced this same problem and what was the fix. Also,
> I would be interested if some of you guys would do this test with your
> radios and let me know if you see the same thing.
> Thanks.
>
>
> --
> FAQ on WWW:               http://www.contesting.com/tentecfaq.htm
> Submissions:              tentec@contesting.com
> Administrative requests:  tentec-REQUEST@contesting.com
> Problems:                 owner-tentec@contesting.com
> Search:                   http://www.contesting.com/km9p/search.htm


--
FAQ on WWW:               http://www.contesting.com/tentecfaq.htm
Submissions:              tentec@contesting.com
Administrative requests:  tentec-REQUEST@contesting.com
Problems:                 owner-tentec@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm