[TenTec] T-T Model 580 Delta Specifications

[Rick Westerman]

I'm replying to my own post to let you know the reflector
stripped the picture of the Delta out of my original post.
It too is available in a direct email.

73
Rick

-----Original Message-----
From: tentec-bounces at contesting.com
[mailto:tentec-bounces at contesting.com]On Behalf Of Rick Westerman
Sent: Saturday, December 27, 2003 8:25 PM
To: tentec at contesting.com
Subject: [TenTec] T-T Model 580 Delta Specifications

Hi guys,

Sorry about the poor quality.  I scanned this into "Word" format
so that I could paste it here on the email.

If anyone is interested in a  "clean" PDF file of this, let me
know and I'll send it to you.  The file is big, though.  It's
about 380 KB.

Remember, back then vendors typically specified "Input Power",
not "Output Power".  So when they said 200w, they were talking
100w by today's standards.

This baby "looks" similar to the old Argosey II.   73 - Rick






SPECIFICATIONS -MODEL 580 DELTA
GENERAL
FREQUENCY BANDS-l.8-2.3, 3.5-4.0, 7.0-7.5, 10.0- 10.5, 14.0-14.5,
18.0-18.5, 21.0-21.5, 24.5-25.0, 28.0-28.5, 28.5-29.0, 29.0-29.5,
29.5-30.0 MHz. (18.0 and 24.5 MHz bands require optional
crystals) (VFO provides approximately 40 kHz over run on each
band edge)
PERMEABILITY TUNED VFO.
VERNIER TUNING-18 kHz per revolution, typical. READOUT -Six
digit, 0.3" LED numerals. Least significant digit indicates 100
Hz.
STABlLITY-VFO frequency change less than 15 Hz per P, averaged
over a 40" change from 70" to 110", after 30 minute warm up. Less
than 10 Hz change from 105 to 125 VAC line voltage when using
TEN- TEC power supply.
PROVISIONS FOR REMOTE VFO-ModeI283.
POWER SWITCH-remotely controls power supply. OPERATING MODES-USB,
LSB, CW. SEMICONDUCTORS-69 Transistors, 19 Integrated cir- cuits,
79 Diodes, 6 Pin Diodes, 1 Large Scale Integrated Circuit, 6 LED
readouts, red.
POWER REQUIRED-l2-14 VDC, 850 mA receive, 18 A maximum transmit.
SIZE-HWD 4:Y."xll %"x15"
WEIGHT -12¥2 Ib.
RECEIVER
WIDEBAND NO-TUNE RF AMPLIFIER. SENSITlVITY-0.3I"V for 10 dB
S+N/N, typical.
RF ATTENUATOR-20 dB resistive.
DYNAMIC RANGE-85 dB minimum. METER-automatically switches to "S"
meter when receiv- ing.
WWV-reception at 10 MHz.
SELECTIVITY-8 pole monolithic ssb filter. 2.4 kHz bandwidth with
2.5 shape factor at 6/60 dB points. Four position selectivity
switch selects standard ssb filter, standard ssb filter with one
section of audio filter, optional 250 Hz or 500 Hz cw filter, or
cw filter
with four additional audio active filters.
AUDIO FILTER SELECTlVITY-Center frequency 750 Hz. One section has
450 Hz bandwidth, down 10 dB at 400 Hz and 1500 Hz.
Four sections have 150 Hz bandwidth, down 40 dB at 400 Hz and
1500 Hz.
NOTCH FILTER-Greater than 50 dB notch, tunable between 200 Hz and
3.5 kHz.
OFFSET TUNING-Receiver, :t 1 kHz, typical.
Built-in 8 ohm speaker.
Less than 2% audio harmonic distortion.
Optional noise blanker, Mode1289.
TRANsMmER
MAXIMUM INPUT POWER-200 watts, ssb and cw. 100% duty cycle for up
to 20 minutes, all bands.
INSTANT BAND CHANGE-No tune-up required.
INSTANT BREAK-IN.
8 pole monolithic ssb filter.
Automatic Level Control with LED indicator. Adjustable threshold
Automatic cw offset of 750 Hz.
Meter indicates SWR when transmitting.
Built-in VOX or PTT.
High impedance microphone input.
Cw sidetone fed into audio amplifier when in cw mode. Sidetone
adjustable for tone and volume, independent of af control.
Front panel MIC and PHONES jacks.
RF OUTPUT IMPEDANCE-50 ohms, nominal.
CARRIER SUPPRESSION-50 dB, minimum. UNWANTED SIDEBAND
SUPPRESSION-50 dB, minimum at 1 kHz tone.
SPURIOUS OUTPUT -Less than -45 dB.




_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec