[TenTec] QSK with QSK-5PC

[Tommy]

What IS full QSK?

Maybe when you hear between dots and your sending  at no more than 
30 wpm. Or is it when you hear between words when your sending at 50 
wpm, Or is it when you know someone is breaking you when your 
sending at 70 wpm? Or is it all of the above?

Tom - W4BQF

----- Original Message ----- 
From: <al_lorona at agilent.com>
To: <tentec at contesting.com>
Sent: Thursday, November 11, 2004 12:38 PM
Subject: RE: [TenTec] QSK with QSK-5PC



Is it full QSK?

Al W6LX



> -----Original Message-----
> From: tentec-bounces at contesting.com
> [mailto:tentec-bounces at contesting.com]On Behalf Of Steve N4LQ
> Sent: Tuesday, November 09, 2004 4:39 PM
> To: tentec at contesting.com
> Subject: Re: [TenTec] QSK with QSK-5PC
>
>
> Phil et al.
> Just to clear up any confusion. I got home from work and checked 
> the
> schematic on this mod. The T voltage is being uses, derived
> from connector
> 61 on the control board. This is driving Q16 which has been
> changed to a
> 2N5554. The emitter remains grounded and the collector runs
> directly to J7,
> the relay output. This is what keys my amp.
>
> Steve N4LQ
> ----- Original Message ----- 
> From: <al_lorona at agilent.com>
> To: <tentec at contesting.com>
> Sent: Tuesday, November 09, 2004 1:01 PM
> Subject: RE: [TenTec] QSK with QSK-5PC
>
>
>
> Hi, Steve,
>
> I believe I know why the previous owner did that to your Omni
> VI. (And I'm
> assuming you care!)
>
> Last night I made some measurements of the TX Enable signal
> on the back
> panel of the Omni VI. This line goes low at the beginning of
> a dit or a dah,
> then the RF comes on, just as it should. There is no problem
> at the leading
> edge.
>
> The problem is at the trailing edge. The TX Enable goes high
> again, but the
> RF doesn't shut off immediately, so there is a period of time
> when the QSK
> circuit in the amp is being told to go back to receive, yet
> there is still
> RF flowing. This is the problem.
>
> What is needed is for this signal to stay low just a little
> bit longer,
> until the RF ends completely, then it can go high again to
> turn the diodes
> in the QSK unit back to receive. There is a signal that will
> do that in the
> Omni; it's called the relay, and that explains why your
> previous owner used
> this signal. This is the line that is affected by the front panel 
> DLY.
>
> I think I am going to do the same as your previous owner.
> That is, I'm going
> to bring out a line from the relay switching transistor, Q16
> on the control
> board, bypass the relay, and use that as my QSK line. I don't
> know if it
> will work yet, but that is my next plan.
>
> True QSK or full QSK, whatever you want to call it, is really hard 
> to
> achieve with an amplifer. The way you guys speak about  QSK on the
> reflector, you aren't happy unless you can hear the band
> between dits at 50
> wpm, but that just isn't possible between an Omni and a cheap
> amp like an
> Ameritron, even with the QSK switch. About the only advantage
> the QSK switch
> affords you is the elimination of the mechanical relay in the amp.
>
> Anyway, that's the way I see it. Thanks again for the
> information you gave
> me.
>
> Regards,
>
> Al  W6LX
>
>
>
>
> > -----Original Message-----
> > From: tentec-bounces at contesting.com
> > [mailto:tentec-bounces at contesting.com]On Behalf Of Steve N4LQ
> > Sent: Monday, November 08, 2004 5:54 PM
> > To: tentec at contesting.com
> > Subject: Re: [TenTec] QSK with QSK-5PC
> >
> >
> > Al. Whatever you do, call MFJ before you hook that thing up.
> > I didn't  and
> > blew diodes out of a rig. My QSK was external which made it
> even more
> > complicated.
> > I can tell you this....The previous owner of my 6+ bypassed
> > the amp relay in
> > the rig and used the txd voltage to drive a little transistor
> > which feeds
> > directly to the amp relay jack. This seems to provide
> > excellent keying for
> > my Icom PW-1 with no sign of hot switching.
> > Steve N4LQ
> > ----- Original Message ----- 
> > From: <al_lorona at agilent.com>
> > To: <tentec at contesting.com>
> > Sent: Monday, November 08, 2004 8:01 PM
> > Subject: [TenTec] QSK with QSK-5PC
> >
> >
> >
> > Would someone who has successfully connected an Omni VI to an
> > Ameritron
> > amplifier equipped with the internal QSK-5PC board be willing
> > to contact me
> > off the list? I want to know how you connected the two.
> >
> > I have read Jim KH7M's previous posts on this subject and
> > they are excellent
> > for the external unit QSK-5, but the connections to the QSK-5PC 
> > are
> > different enough that I cannot translate the connections in my 
> > head.
> >
> > Interestingly, a search of the Internet yields no information
> > whatsoever on
> > this. I am thinking of using the TX enable input on the back
> > of the Omni to
> > receive a handshaking signal from the QSK-5PC, but I want to 
> > talk to
> > somebody who has done this.
> >
> > Thanks.
> >
> > Al  W6LX
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec at contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec at contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec