[TenTec] PSK31 & the Argonaut V

[tom]

I take the low tech approach to solving this problem. I sometimes use an amplifier with my Argo, so I already have a foot switch to control the amp and the argo. So for tx/rx control on psk31 I just step on the switch and start typing. 

Tom
K4NOX
-----Original Message-----
From: "Charles Nagel" <cnagel at sbcglobal.net>
Date: Tue, 19 Apr 2005 08:55:19 
To:"'Discussion of Ten-Tec Equipment'" <tentec at contesting.com>
Subject: Re: [TenTec] PSK31 & the Argonaut V

Hi Jim,

I used the ARGO V with DIGIPAN 2.0 with no trouble whatever. You might
want to try this software. I assume you are using the optional fan when
running the ARGO at full output when operating PSK31. Set the microphone
gain at minimum and the output of the sound card as low as possible. If
I recall my VOX setting was at about 6. Then bring up the mic gain - not
much - just until the rig kicks into action. You need to play around
with it a bit. Then if you don't have a PSK meter get a report from
someone right away on the signal quality. Also if you have another
receiver you can get an idea of the signal quality but you probably know
this already. DIGIPAN 2.0 works well also with my Jupiter and Orion.
It's the only software I have ever used so I can only speak to its
operation.

Charles, K0CW

-----Original Message-----
From: tentec-bounces at contesting.com
[mailto:tentec-bounces at contesting.com] On Behalf Of We5f at aol.com
Sent: Monday, April 18, 2005 11:11 PM
To: tentec at contesting.com
Subject: [TenTec] PSK31 & the Argonaut V

Hello to the group:

I am a proud owner of a new Argonaut V.  This past weekend I hooked up a

serial 
cable from my laptop to the rig, and the aux cable to the mic input and 
speaker 
output jacks on that laptop.  The Argo instructions say that is all I
need to 
work 
PSK31.

No problem running Ham Radio Deluxe to control the rig.  Everything
works FB. 
 I do 
wish the Argonaut had an instruction for controlling volume from the 
software.

However I can't get the PSK31 program that comes with HRD to reliably
switch 
the 
Argo from RX to TX and back again.  I selected "soundcard control of
PTT" in 
the 
program.  I'm trying to use the laptop soundcard to activate the rig's
vox.  
I have the 
Argo VOX set for low gain and the ANTIVOX set high, as advised in the
manual.

Most of the time, the TX putton on the PSK31 screen doesn't function.  
Occasionally, 
I've gotten it to key the rig to transmit and send my message.  However,
when 
I 
hit "escape", the Argo just "locks up" and won't switch back to receive
(or 
do anything, for that matter).  I have to turn the Argo off  and back on
again 
to reset it to get it to receive again.

Has anyone else experienced this?  What's the fix?  I may be making this
more 

difficult than need be.  I'd like to hear what setup other Argo owners
are 
using to 
run both Ham Radio Deluxe and PSK31 together.

TIA/73, Jim K5HO

---------------------
Nunquam Secundum
_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

Sent via BlackBerry - a service from AT&T Wireless.