[TenTec] NO XMIT WITH PTT

[Carl Moreschi]

Ron,

If you have nothing plugged into TXEN and TXOUT on the pegasus, then TXLoop
must be off to allow transmit.  If turning TXLoop on causes it to transmit
with nothing plugged into TXEN and TXOUT, then clearly you have a hardware
problem.  These are amplifier timing connections.  Without an amplifier,
TXLoop should always be off, and nothing should be plugged into TXEN and
TXOUT on the back of the rig.  Maybe you have something plugged in these
jacks by mistake.

73,

Carl Moreschi N4PY
Franklinton, NC
----- Original Message ----- 
From: "Ron" <k8fg at sbcglobal.net>
To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
Sent: Sunday, March 20, 2005 6:14 PM
Subject: Re: [TenTec] NO XMIT WITH PTT


> Steve N4LQ wrote:
>
> >I don't quiet follow you. Are you saying if you left click the TX Loop
> >button at the top, it goes into transmit or do you mean it allows you to
go
> >into transmit? If it's the former, it almost sounds like your PTT line is
> >shorted somewhere and when you "close the loop" in software, it
transmits.
> >I still think you should download the TT software and try it first. That
> >will eliminate some confusion since it's rather basic.
> >Check the PTT voltage at the jack per the manual between Gnd and Ptt. You
> >should have between 4 and 5 volts.
> >Steve Ellington
> >N4LQ at iglou.com
> >----- Original Message ----- 
> >From: "Ron" <k8fg at sbcglobal.net>
> >To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
> >Sent: Sunday, March 20, 2005 4:57 PM
> >Subject: Re: [TenTec] NO XMIT WITH PTT
> >
> >
> >
> >
> >>Steve N4LQ wrote:
> >>
> >>
> >>
> >>>Ron
> >>>Tx Loop button? What's that? In the "Transmitter" menu, I have a
"Enable
> >>>keying loop" button. Is that what you meant? I have mine disabled since
I
> >>>don't use a TT amp with the Peg. On your N4PY front panel, do you have
the
> >>>"Xmit Disable" activated? If so, disable it. Also check the "ACCInp"
> >>>button.
> >>>For microphone input it should be disabled.
> >>>If all this doesnt work, try the basic TenTec software and start all
over.
> >>>Out of ideas. 73
> >>>Steve Ellington
> >>>N4LQ at iglou.com
> >>>----- Original Message ----- 
> >>>From: "Ron" <k8fg at sbcglobal.net>
> >>>To: <tentec at contesting.com>
> >>>Sent: Saturday, March 19, 2005 2:16 PM
> >>>Subject: [TenTec] NO XMIT WITH PTT
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>>Hello to the Group,
> >>>>I have a couple of questions .
> >>>>I have a Pegasus that will not Xmit via the Mic or Acc jacks
> >>>>but will key via the N4PY software with a mouse click on the
> >>>>TX Loop button.. Any ideas ?
> >>>>
> >>>>Also is there ant service info available ?
> >>>>Thanks, Ron/K8FG...
> >>>>_______________________________________________
> >>>>TenTec mailing list
> >>>>TenTec at contesting.com
> >>>>http://lists.contesting.com/mailman/listinfo/tentec
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>_______________________________________________
> >>>TenTec mailing list
> >>>TenTec at contesting.com
> >>>http://lists.contesting.com/mailman/listinfo/tentec
> >>>
> >>>
> >>>
> >>>
> >>>
> >>Hi Steve and Carl,
> >>I have the latest ver of software and in the top row of buttons there is
> >>a Tx Loop button after the Calibrate.
> >>When I left click on this button it will go into xmit. If I go into the
> >>settings/transmitter menu and
> >>uncheck Keying Loop the rig goes into xmit. ACCInp is disabled.
> >>I am starting to believe I have a rig problem, if I short the Ptt pin in
> >>the mic connector to ground
> >>there is no xmit also did the same test with the Acc connector with the
> >>same results.
> >>Ron/K8FG...
> >>_______________________________________________
> >>TenTec mailing list
> >>TenTec at contesting.com
> >>http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >>
> >>
> >
> >_______________________________________________
> >TenTec mailing list
> >TenTec at contesting.com
> >http://lists.contesting.com/mailman/listinfo/tentec
> >
> >
> >
> Hi Steve,
> When I left click the button it xmit's. I just checked the ptt voltage,
> it reads -.707 I don.t have a manual
> other than basic operation.
> Ron/K8FG...
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec