[TenTec] 705 Mic Low Output Help Request

[john ferro]

i had somewhat low output (voice peaks) on my paragon with a shure 444d mic - although audio reports were always excellent - when i switched to a ten tec mike the voice peaks went through the roof and now i am completely satisfied - i can see you are already using a ten tec mic - have you tried a different one?
 
thx, john> From: d.e.warnick at comcast.net> To: tentec at contesting.com> Date: Mon, 4 Feb 2008 19:15:15 +0000> Subject: Re: [TenTec] 705 Mic Low Output Help Request> > My 705 microphone manual shows pin 4 as Plus Electret Voltage (7 to 14) VDC).> > My Omni VI+ manuas shows the transciever supplying +4 volts to the mic, although no-load measurement at the mic connector shows 9.44 volts using a Fluke 77 multimeter.> > The only modification shown in the 705 manual is to a Corsair Transciever.> > I hope this helps. Also, at the risk of sounding like a broken record, I cannot overemphasize the value of manuals for all your TenTec gear. The absolute best first source for this information is TenTec. Their tech line is also the best if you need help> > Dave> WA3MKB> -------------- Original message -------------- > From: "David & Chris Drake" <drakes at psci.net> > > > Don't remember for sure without looking it up. But I think 9-12v. The mic > > runs off a 9v battery if not getting power directly, so it would make sense > > it needs around 9v to work. > > David > > > > -----Original Message----- > > From: tentec-bounces at contesting.com [mailto:tentec-bounces at contesting.com] > > On Behalf Of Greg Kuczek > > Sent: Monday, February 04, 2008 9:15 AM > > To: Discussion of Ten-Tec Equipment > > Subject: Re: [TenTec] 705 Mic Low Output Help Request > > > > > > I'm running it thru the jack. I haven't checked the voltage at the jack yet, > > thanks. Do you know what the voltage should be? > > > > 73 > > Greg W9VOX > > > > David & Chris Drake wrote: > > Are you running the 705 by battery or through the Omni V? If through the > > Omni V, check the voltage at the jack first. If by battery, check the > > battery. Then check the plug before going inside it. > > Good luck, > > David > > > > ----- Original Message ----- > > From: "Greg Kuczek" > > To: > > Sent: Sunday, February 03, 2008 10:23 PM > > Subject: [TenTec] 705 Mic Low Output Help Request > > > > > > >I have a 705 mic that I am having low output problems when used with an > > >Omni V. I've read that you can change out the R11 resisitor to 3300 ohms to > > > > >help correct this. Unfortunately I don't have a schematic or any > > >documentation to help me locate this resistor. Any help identifying R11 > > >would be appreciated. > > > > > > 73 de Greg W9VOX _______________________________________________ > > > TenTec mailing list > > > TenTec at contesting.com > > > http://lists.contesting.com/mailman/listinfo/tentec > > > > > > > > > > > > _______________________________________________ > > TenTec mailing list > > TenTec at contesting.com http://lists.contesting.com/mailman/listinfo/tentec > > > > _______________________________________________ > > TenTec mailing list > > TenTec at contesting.com http://lists.contesting.com/mailman/listinfo/tentec > > > > > > _______________________________________________ > > TenTec mailing list > > TenTec at contesting.com > > http://lists.contesting.com/mailman/listinfo/tentec > _______________________________________________> TenTec mailing list> TenTec at contesting.com> http://lists.contesting.com/mailman/listinfo/tentec
_________________________________________________________________
Shed those extra pounds with MSN and The Biggest Loser!
http://biggestloser.msn.com/