[TenTec] 041 firmware rev

[John Sheeley]

You might try a battery reset then a master reset. then try re flashing the Orion II

John wb4qda



----- Original Message ----
From: Jim M. <jmiller1706 at cfl.rr.com>
To: Discussion of Ten-Tec Equipment <tentec at contesting.com>
Sent: Friday, February 27, 2009 3:51:35 PM
Subject: Re: [TenTec] 041 firmware rev

Be very careful guys, I now cannot get the previous version to work.
Downloads to the O2 OK, but the controls do not work.  Guess it's back to
the factory.

-----Original Message-----
From: tentec-bounces at contesting.com [mailto:tentec-bounces at contesting.com]
On Behalf Of Jim M.
Sent: Friday, February 27, 2009 4:42 PM
To: 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] 041 firmware rev

On the phone with TT, he suggested various reset sequences but the load
won't work.  Said file might have been corrupted and to download it again,
still no luck.  Now reverting back to previous version, hope I didn't crash
my radio.  Could someone give me that download site again just to be sure?

-----Original Message-----
From: tentec-bounces at contesting.com [mailto:tentec-bounces at contesting.com]
On Behalf Of kc9cdt at aol.com
Sent: Friday, February 27, 2009 4:13 PM
To: tentec at contesting.com
Subject: Re: [TenTec] 041 firmware rev

Make sure stop on error is ON,
Lee










-----Original Message-----
From: Jim M. <jmiller1706 at cfl.rr.com>
To: 'Discussion of Ten-Tec Equipment' <tentec at contesting.com>
Sent: Fri, 27 Feb 2009 4:04 pm
Subject: Re: [TenTec] 041 firmware rev



Well not having a lot of luck here.  Somehow crashed the O2 first time
trying with an old serial card in the PC, and it was very slow.  Got a USB
to serial converter and it flashed in about 5 mins this time but nothing in
the radio works, no knob, no buttons, and the display reads all zeros
frequency.  Am trying the flash again.  Stay tuned.  So far I am
underwhelmed.

-----Original Message-----
From: tentec-bounces at contesting.com [mailto:tentec-bounces at contesting.com]
On Behalf Of Peter Frenning [OZ1PIF]
Sent: Friday, February 27, 2009 3:57 PM
To: Ron Castro; Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] 041 firmware rev

Ron Castro skrev:
> I have noticed that the levels between the AF and RF AGC's are quite 
> different.  The AF is very low compared to RF.
>
>          Ron Castro
>  Chief Technical Officer
>     Results Radio, LLC
>                N6IE
>      www.N6IE.com
>  
Same here, but doesn't seem to have detrimental effects other than you 
have to twist up the AF encoder...

-- 
Vy 73 de OZ1PIF/5Q2M, Peter

** CW: Who? Me? You must be joking!! **
email: peter(no-spam-filler)@frenning.dk
http://www.frenning.dk/oz1pif.htm
Ph. +45 4619 3239
Snailmail:
Peter Frenning
Ternevej 23
DK-4130 Viby Sj.
Denmark
***********************************


_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec