[TenTec] [dxlab] HRD & DXLab

CSM(r) Gary Huber glhuber at msn.com
Sat Aug 7 17:31:30 PDT 2010


OMNI-VII Receive and Transmit Modes for use with DXLab Commander

The following commands were derived from page 18 of OMNI-VII, Model 588, 
Programmer's Reference Guide, Revision 1.009 which is available at 
<http://www.tentec.com/?id=2> and from 
<http://www.dxlabsuite.com/commander/Help/CommandSequences.htm>.

Button        ( command  )      what it does

F-5 [ USB ]  ( '*M13<13> )  sets VFOA to USB,  VFOB to CWU

F-6 [ LSB ]  ( '*M25<13> )  sets VFOA to LSB,  VFOB to CWL

F-7 [ CW ]  ( '*M31<13> )  sets VFOA to CWU,  VFOB to USB

F-8 [ AM ]  ( '*M02<13> )  sets  VFOA to AM,  VFOB to LSB

Note: by using the front panel A/B button,  set the VFO with the TRANSMIT 
mode desired to the DX pile frequency and adjust the bandwidth as desired. 
In the same manner set opposite VFO to the DX ( your receive) and adjust the 
bandwidth as desired.  On the Commander panel split VFOs by checking the 
"Split" box,  mouse over, click on and hold the XFC button to monitor the 
pile or manually tune the VFO via the OMNI-VII (BIG knob), release to 
transmit from a frequency in the pile (DX's receive frequency).

F-9 [ U-U ]  ( '*M11<13> ) sets both VFOs to USB

F-10 [ L-L ]  ( '*M22<13> ) sets both VFOs to LSB

F-11 [ UC-UC ] ( '*M33<13>) sets both VFOs to CWU

F-12 [ AM-AM]  ( '*M00<13>) sets both VFOs to CWU

Questions - email glhuber at msn.com

73,

Gary - AB9M

--------------------------------------------------
From: "CSM(r) Gary Huber" <glhuber at msn.com>
Sent: Saturday, August 07, 2010 6:16 PM
To: <dxlab at yahoogroups.com>
Cc: "TenTec Reflector" <tentec at contesting.com>; 
<Ten-Tec-Omni-VII at yahoogroups.com>
Subject: Re: [TenTec] [dxlab] HRD & DXLab

> On a related note, I will submit the Commander command sequences for 
> OMNI-VII TX/RX VFO mode splits later this evening.
>
> By using a different mode in each VFO, different bandwidths may be used 
> for the DX and the pile.
>
> 73,
>
> Gary - AB9M
>
>
> From: Dave AA6YQ
> Sent: Saturday, August 07, 2010 12:01 PM
> To: dxlab at yahoogroups.com
> Subject: RE: [dxlab] HRD & DXLab
>
>
>
>>>>AA6YQ comments below
>
> -----Original Message-----
> From: dxlab at yahoogroups.com [mailto:dxlab at yahoogroups.com]On Behalf Of
> Jerry Keller (K3BZ)
> Sent: Saturday, August 07, 2010 12:57 PM
> To: (REFLECTOR) DXLAB
> Subject: [dxlab] HRD & DXLab
>
> I keep hearing about HRD and thought I'd try it with DXLab, just for fun.
> Couple questions:
> Has the new HRD matured enough now for use with DXLab? (with HRD Bridge)
>
>>>>As far as I know, HRD still can't be directed to set VFO B or
> enable/disable split, so if you double-click a Spot Database Entry for a
> station operating split, you'll have to manually setup your transceiver 
> for
> split frequency operation.
>
> If I install HRD Bridge and HRD, and don't like it, is it easy to reverse
> the process and get back where I was?
>
>>>>Yes -- you'd simply terminate HRD and the HRD bridge, and run Commander
> instead.
>
> 73,
>
> Dave, AA6YQ
>
>
>
> __._,_.___
> Reply to sender | Reply to group | Reply via web post | Start a New Topic
> Messages in this topic (2)
> Recent Activity: a.. New Members 6 a.. New Files 2
> Visit Your Group
> MARKETPLACE
> Stay on top of your group activity without leaving the page you're on - 
> Get the Yahoo! Toolbar now.
>
>
>
> --------------------------------------------------------------------------------
>
> Get great advice about dogs and cats. Visit the Dog & Cat Answers Center.
>
>
>
> --------------------------------------------------------------------------------
>
> Hobbies & Activities Zone: Find others who share your passions! Explore 
> new interests.
>
>  Switch to: Text-Only, Daily Digest . Unsubscribe . Terms of Use.
>
> __,_._,___
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 


More information about the TenTec mailing list