[TenTec] Popping in O1 audio during AF adjust

[art davis]

Nope, I spoke too soon. It's back and this time the resets don't affect it. Please post what their solution turns out to be for you.

> Date: Wed, 14 Jul 2010 22:07:08 -0400
> From: reed.krenn at gmail.com
> To: tentec at contesting.com
> Subject: Re: [TenTec] Popping in O1 audio during AF adjust
> 
> I am going to be *so* embarrassed if that's all it is......
> 
> BUT, I do have them looking at another trouble.
> 
> -- Reed / WW3A
> 
> On Wed, Jul 14, 2010 at 7:29 PM, art davis <n4uc at hotmail.com> wrote:
> 
> >
> >
> >
> >
> >
> >
> > Here is the response I got from the TenTec service manager within 3 hours
> > of me posting this. Now that's service!
> >
> > First do RAM clear reset followed by a master reset and
> > clear user memories
> >
> > and filter settings should be performed. RAM clear is as follows:
> >
> > 1. Orion off, power supply on.
> >
> > 2. Press and hold the LCK button just below the VFO B knob.
> >
> > 3.Turn on Orion and continue to hold the LCK button until Master Reset
> > is
> >
> > displayed on the screen. BATTERY FAILURE may also be displayed,
> > disregard.
> >
> > 4. Release the LCK button and allow the Orion to boot to 14.250.
> >
> > 5. Turn the Orion Off and perform the Master Reset using The MAIN RX/TX
> >
> > button. User memories and filter settings MUST be cleared.
> >
> > It took care of it for me...gud luck
> >
> > > Date: Wed, 14 Jul 2010 18:50:12 -0400
> > > From: reed.krenn at gmail.com
> > > To: tentec at contesting.com
> > > Subject: Re: [TenTec] Popping in O1 audio during AF adjust
> > >
> > > I misspoke; mine also occurs with rotation of either of the VFO encoders.
> > >
> > > -- Reed / WW3A
> > >
> > > On Wed, Jul 14, 2010 at 6:45 PM, Reed Krenn <reed.krenn at gmail.com>
> > wrote:
> > >
> > > > I just shipped my (Classic) Orion to Ten Tec *today* for the exact same
> > > > problem.
> > > >
> > > > I'll report the results to the reflector.
> > > >
> > > > Reed / WW3A
> > > >
> > > >
> > > > On Tue, Jul 13, 2010 at 11:30 PM, art davis <n4uc at hotmail.com> wrote:
> > > >
> > > >>
> > > >> My O1 (2.0.6.2a) has recently developed a popping in the left audio
> > > >> channel of the headphone output when adjusting the volume of either
> > the MAIN
> > > >> or SUB AF. The rate of the popping seems to be in sync with the
> > rotation of
> > > >> the AF controls (optical encoder?) and its volume goes up and down
> > with the
> > > >> audio volume. In the headphones it sounds just like you ears popping
> > during
> > > >> flying or diving under water. The popping is not affected by the mode,
> > RF
> > > >> gain, sidetone volume, MON setting, or any other front panel control
> > > >> setting, except as described for the AF controls.
> > > >> Any ideas?
> > > >>
> > > >>
> > > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec at contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _________________________________________________________________
> > The New Busy is not the too busy. Combine all your e-mail accounts with
> > Hotmail.
> >
> > http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4
> > _______________________________________________
> > TenTec mailing list
> > TenTec at contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
 		 	   		  
_________________________________________________________________
Hotmail has tools for the New Busy. Search, chat and e-mail from your inbox.
http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_1