[TenTec] having problem getting amp to work with Orion II

[John Molenda]

Roger , I double checked that and thanks .  John
----- Original Message ----- 
From: "John" <fraz1 at bellsouth.net>
To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
Sent: Monday, March 22, 2010 7:18 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II


> John....just checking the obvious.  On the back of the O II, the TX en and
> out are in the vertical plane.  IE, one above the other.  Make sure you 
> have
> the both cables under the same keying loop (either 1 or 2).
>
> 73 W4II
> ----- Original Message ----- 
> From: "John Molenda" <brazos at rochester.rr.com>
> To: <ac5aa at ac5aa.com>; "Discussion of Ten-Tec Equipment"
> <tentec at contesting.com>
> Sent: Monday, March 22, 2010 6:02 PM
> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>
>
>> roger coax connected
>> ----- Original Message ----- 
>> From: "Duane Calvin" <ac5aa1 at gmail.com>
>> To: "'Discussion of Ten-Tec Equipment'" <tentec at contesting.com>
>> Sent: Monday, March 22, 2010 6:51 PM
>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>
>>
>>> Oops - three cables - don't forget the exciter RF!  :-)
>>>
>>> Duane Calvin, AC5AA
>>> Austin, Texas
>>> www.ac5aa.com
>>>
>>>
>>> -----Original Message-----
>>> From: tentec-bounces at contesting.com
>>> [mailto:tentec-bounces at contesting.com]
>>> On Behalf Of John
>>> Sent: Monday, March 22, 2010 5:35 PM
>>> To: Discussion of Ten-Tec Equipment
>>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>>
>>> That is correct John!
>>>
>>> 73 John W4II
>>> ----- Original Message ----- 
>>> From: "John Molenda" <brazos at rochester.rr.com>
>>> To: "aa4nn" <aa4nn at earthlink.net>; "Discussion of Ten-Tec Equipment"
>>> <tentec at contesting.com>
>>> Sent: Monday, March 22, 2010 5:19 PM
>>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>>
>>>
>>>>I have reread the manual and looked at the hookup my question is this
>>>>(when
>>>> hooking Orion II to titan III amp ) there are only two cables to run
>>>> between
>>>> the two tx en out  key in out .  and then use the switch on the amp in
>>>> qsk
>>>> mode .  then go to the tx menu and enable loop 1 .  is this correct am 
>>>> I
>>>> missing a hookup ?  thanks John kb2huk
>>>> ----- Original Message ----- 
>>>> From: "aa4nn" <aa4nn at earthlink.net>
>>>> To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
>>>> Sent: Monday, March 22, 2010 9:14 AM
>>>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>>>
>>>>
>>>>> Does the term QSK or PTT ring a bell?
>>>>> de Joe, aa4nn
>>>>> Lake Wylie, SC
>>>>> ------------------------------------------------------
>>>>>>> Hello all , I am having a problem getting my Orion II to work with 
>>>>>>> my
>>>>>>> Titan III
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec at contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec at contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>>> ----------------------------------------------------------------------------
>>> ----
>>>
>>>
>>>
>>> No virus found in this incoming message.
>>> Checked by AVG - www.avg.com
>>> Version: 8.5.437 / Virus Database: 271.1.1/2763 - Release Date: 03/22/10
>>> 07:33:00
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> --------------------------------------------------------------------------------
>
>
>
> No virus found in this incoming message.
> Checked by AVG - www.avg.com
> Version: 8.5.437 / Virus Database: 271.1.1/2763 - Release Date: 03/22/10
> 07:33:00
>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>