[TenTec] having problem getting amp to work with Orion II

[N4PY2]

John,

What I'm trying to do is diagnose what is going on.  If you turn on the 
Orion keying loop and do not connect anything between TXEN and TXOUT, 
transmit will be blocked.  If you then jumper TXEN and TXOUT together 
without the amp connected, the Orion should work alone and normally.  So, 
does this work this way?  If this does, then the problem is in the amp.  If 
it doesn't, then the problem is in the Orion.

Carl Moreschi N4PY
121 Little Bell Drive
Hays, NC 28635
www.n4py.com


----- Original Message ----- 
From: "John Molenda" <cdistflatfoot at gmail.com>
To: "N4PY2" <n4py2 at earthlink.net>; "Discussion of Ten-Tec Equipment" 
<tentec at contesting.com>
Sent: Tuesday, March 23, 2010 2:24 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II


> carl could you please clairify #2  thanks  John
> ----- Original Message ----- 
> From: "N4PY2" <n4py2 at earthlink.net>
> To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
> Sent: Monday, March 22, 2010 10:32 PM
> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>
>
>> John,
>> >
>> 1) Turn on TXloop for antenna 1 on the orion.
>> 2) Connect TXEN to TXOUT on the Orion.
>>
>> Does the Orion now key when you try to transmit?  It should.
>>
>> If that works, then connect TXOUT to the Titan key in.  Connect the Titan
>> key out to the Orion TXEN.  The Orion should still key.  So exactly what
>> does not work.
>>
>> Carl Moreschi N4PY
>> 121 Little Bell Mountain Dr
>> Hays, NC 28635
>> www.n4py.com
>>
>> Try this:
>
>>
>> ----- Original Message ----- 
>> From: "John Molenda" <cdistflatfoot at gmail.com>
>> To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
>> Sent: Monday, March 22, 2010 9:15 PM
>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>
>>
>>>I just check continuity of the two rca plugs and the coax it checks out
>>>good
>>> .  John kb2huk
>>> ----- Original Message ----- 
>>> From: "John Molenda" <brazos at rochester.rr.com>
>>> To: <ac5aa at ac5aa.com>; "Discussion of Ten-Tec Equipment"
>>> <tentec at contesting.com>
>>> Sent: Monday, March 22, 2010 7:02 PM
>>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>>
>>>
>>>> roger coax connected
>>>> ----- Original Message ----- 
>>>> From: "Duane Calvin" <ac5aa1 at gmail.com>
>>>> To: "'Discussion of Ten-Tec Equipment'" <tentec at contesting.com>
>>>> Sent: Monday, March 22, 2010 6:51 PM
>>>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>>>
>>>>
>>>>> Oops - three cables - don't forget the exciter RF!  :-)
>>>>>
>>>>> Duane Calvin, AC5AA
>>>>> Austin, Texas
>>>>> www.ac5aa.com
>>>>>
>>>>>
>>>>> -----Original Message-----
>>>>> From: tentec-bounces at contesting.com
>>>>> [mailto:tentec-bounces at contesting.com]
>>>>> On Behalf Of John
>>>>> Sent: Monday, March 22, 2010 5:35 PM
>>>>> To: Discussion of Ten-Tec Equipment
>>>>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>>>>
>>>>> That is correct John!
>>>>>
>>>>> 73 John W4II
>>>>> ----- Original Message ----- 
>>>>> From: "John Molenda" <brazos at rochester.rr.com>
>>>>> To: "aa4nn" <aa4nn at earthlink.net>; "Discussion of Ten-Tec Equipment"
>>>>> <tentec at contesting.com>
>>>>> Sent: Monday, March 22, 2010 5:19 PM
>>>>> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>>>>>
>>>>>
>>>>>>I have reread the manual and looked at the hookup my question is this
>>>>>>(when
>>>>>> hooking Orion II to titan III amp ) there are only two cables to run
>>>>>> between
>>>>>> the two tx en out  key in out .  and then use the switch on the amp 
>>>>>> in
>>>>>> qsk
>>>>>> mode .  then go to the tx menu and enable loop 1 .  is this correct 
>>>>>> am
>>>>>> I
>>>>>> missing a hookup ?  thanks John kb2huk
>>>>>> ----- Original Message ----- 
>>>>>> From: "aa4nn" <aa4nn at earthlink.net>
>>>>>> To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
>>>>>> Sent: Monday, March 22, 2010 9:14 AM
>>>>>> Subject: Re: [TenTec] having problem getting amp to work with Orion 
>>>>>> II
>>>>>>
>>>>>>
>>>>>>> Does the term QSK or PTT ring a bell?
>>>>>>> de Joe, aa4nn
>>>>>>> Lake Wylie, SC
>>>>>>> ------------------------------------------------------
>>>>>>>>> Hello all , I am having a problem getting my Orion II to work with
>>>>>>>>> my
>>>>>>>>> Titan III
>>>>>>> _______________________________________________
>>>>>>> TenTec mailing list
>>>>>>> TenTec at contesting.com
>>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>>
>>>>>> _______________________________________________
>>>>>> TenTec mailing list
>>>>>> TenTec at contesting.com
>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>>
>>>>> ----------------------------------------------------------------------------
>>>>> ----
>>>>>
>>>>>
>>>>>
>>>>> No virus found in this incoming message.
>>>>> Checked by AVG - www.avg.com
>>>>> Version: 8.5.437 / Virus Database: 271.1.1/2763 - Release Date:
>>>>> 03/22/10
>>>>> 07:33:00
>>>>>
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec at contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec at contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec at contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec