[TenTec] OrionII and MixW Config settings

[Bob McGraw - K4TAX]

OK, so the convention for AFSK is LSB.  My goof!   Guess I've been operating 
too much PSK-31 which does typically use the USB mode regardless of band 
convention.  Actually, either sideband will decode correctly in PSK-31.

Thanks for the clarification.  LSB for AFSK.

73
Bob, K4TAX


----- Original Message ----- 
From: "Stan Brock" <sales at tentec.com>
To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
Sent: Friday, November 16, 2012 12:35 PM
Subject: Re: [TenTec] OrionII and MixW Config settings


> Bob,
>
> I think for AFSK you want to be in LSB instead of USB.
>
> Stan
>
> On Thu, Nov 15, 2012 at 3:48 PM, Bob McGraw - K4TAX 
> <RMcGraw at blomand.net>wrote:
>
>> Tony:
>>
>> You mention FSK,  the MixW program provides AFSK and not a FSK signal
>> although it says RTTY.  For AFSK the Orion should be in USB mode.  Check
>> the value of the Line/Aux Gain as it may be 0 or too low.  Raise the
>> Line/Aux gain to a mid way value to start.   Also the Windows Mixer will
>> adjust the audio level going to the radio.
>>
>> From MixW drop down menu select Configure and then  Output volume.  This
>> brings up the Windows Mixer.  The two sliders marked Volume Control and
>> Wave are the controls for the audio out of the computer.   I normally run
>> mine about mid range and then adjust the Wave slider for some 30 to 40
>> watts of data power output.  The Orion should be set to 100 watts power 
>> and
>> the Speech Processor should be off.
>>
>> 73
>> Bob, K4TAX
>>
>>
>>
>>
>> ----- Original Message ----- From: "EI6DL" <ei6dl at eircom.net>
>>
>> To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
>> Sent: Wednesday, November 14, 2012 3:13 PM
>>
>> Subject: [TenTec] OrionII and MixW Config settings
>>
>>
>>  Hello ! I have just connected the TenTec Model 712 USB to the Aux/I on 
>> my
>>> Orion II and ran MixW on my PC .The programme is reading the Digi fsk
>>> signals ok but i can not get the programme configed to transmit /send a 
>>> sig
>>> I have the programme set for the TenTec Orion II and have gone into the
>>> menu on the Orion II and changed the TX Audio source to Aux instead
>>> Mic.Still will not force the transciever to TX a digi sig ?? Can anyone
>>> help ? 73'es Tony EI6DL
>>> ______________________________**_________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/**mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec>
>>>
>>>
>>
>> ______________________________**_________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/**mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec>
>>
>
>
>
> -- 
> Stan Brock, WD0BGS
> Amateur Radio Sales
> Ten-Tec, Inc.
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>