[TenTec] Need push on/off pots for Omni C

[Richard Detweiler]

Thanks,
 
I have " restored " many of these OMNI A/B/C/D radios,  much easier to work on than the modern ones and more suited to my 'old' knowledge :)
 
I've had to repair just about everything at least once,  if you need any advice, just give me a yell.

Best Wishes
Richard

K5SF


 
> Date: Wed, 12 Jun 2013 21:29:36 -0700
> From: rfulco at bellsouth.net
> To: tentec at contesting.com
> Subject: Re: [TenTec] Need push on/off pots for Omni C
> 
> I spent 3 hours on it, pulled front panel and then unsolder/pulled the pots. I actually was able to pull them apart, and push the shaft in and out to get it unstuck and then put some grease in and put them all back together and make it work as new. Once you get the pot out not as hard as I thought. Only problem, the S meter has some corrosion, and the fine wire is broke inside! I was on my way to getting this trash can Omni back to life...Got the speaker ps going last night..Now to just find a old S meter! Thank for reply..Randy
> 
> --- On Wed, 6/12/13, Richard Detweiler <rdetweil at hotmail.com> wrote:
> 
> 
> From: Richard Detweiler <rdetweil at hotmail.com>
> Subject: Re: [TenTec] Need push on/off pots for Omni C
> To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
> Date: Wednesday, June 12, 2013, 11:35 AM
> 
> 
> Randy,  
> 
> 
> 
> Those are very hard to find,  some people ran 12V through the power switch and burned them as there weren't designe for that current.  
> 
> There were only meant to power the AC line to the power supply.
> 
> 
> 
> Best find any push/pull pot of any value then replace the resistor plate with one that works or the original if not damaged.
> 
> 
> 
> I have a surplus store here that sells the 100 ohm version in the same body style,
> 
> 
> 
> What I have done in the past is open the front of the 100 ohm one by lifting the tabs and then replaced the carbon resistor plate with the correct value.
> 
> 
> 
> If you can't use the original plate,  Make sure you find the right type of resistor plate,  there is a  audio taper and a linear taper.
> 
> 
> 
> Hope that help.
> 
> Best Wishes
> Richard
> K5SF
> 
> 
> 
> > Date: Tue, 11 Jun 2013 23:22:53 -0700
> > From: rfulco at bellsouth.net
> > To: tentec at contesting.com
> > Subject: [TenTec] Need push on/off pots for Omni C
> > 
> > I picked up a neglected Omni C with matching supply/speaker this weekend at Hamfest. Lots of oxidation/ rust on bolts on inside. I free'd up most pots, but  the push on/off with pots --don't move in or out. Anyone got any spare's they want to part with? Randy K5SL
> > _______________________________________________
> > TenTec mailing list
> > TenTec at contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>                           
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec