[TenTec] Eagle 9MHz tap questions.

[Carl Moreschi]

Yes, my software does all the syncing.  And this connection is fully 
protected from transmit power.

Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
www.n4py.com

On 12/23/2014 8:52 AM, Rick - DJ0IP / NJ0IP wrote:
> Oh, you mean just tap into the antenna line as it runs through the RX.
> Now that's a piece of cake.
>
> But that is effectively just feeding the TX antenna out to another RX.
> How do you sync the ext radio to be on the same band as the Eagle?
> I guess your software talks to both and takes care of that...?
>
> 73 - Rick, DJ0IP
> (Nr. Frankfurt am Main)
>
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces at contesting.com] On Behalf Of Carl
> Moreschi
> Sent: Tuesday, December 23, 2014 1:52 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Eagle 9MHz tap questions.
>
> Rick,
>
> You can just put a Y connector between the two preselector jacks and run the
> third leg to a panadapter radio such as the Softrock Ensemble II.
> This works great.  My software will keep the softrock and Eagle on the same
> frequency.
>
> Carl Moreschi N4PY
> 58 Hogwood Rd
> Louisburg, NC 27549
> www.n4py.com
>
> On 12/23/2014 1:18 AM, Drago wrote:
>>
>>
>> -----Izvorna poruka----- From: Rick - DJ0IP / NJ0IP Sent: Tuesday,
>> December 23, 2014 5:32 AM To: 'Discussion of Ten-Tec Equipment' Subject:
>> Re: [TenTec] Eagle 9MHz tap questions.
>> I was wanting to add a pan-adapter.
>> I may have to replace a board in order to do that.
>> My unit does not have the TMP jack with the 9 MHz out.
>>
>> Also I have to find a way to run the signal out the back.
>> I already have two spare RCA Phono jacks in use for the pre-selector.
>>
>> 73 - Rick, DJ0IP
>> (Nr. Frankfurt am Main)
>>
>> -----Original Message-----
>> From: TenTec [mailto:tentec-bounces at contesting.com] On Behalf Of
>> Richards
>> Sent: Tuesday, December 23, 2014 2:49 AM
>> To: Discussion of Ten-Tec Equipment
>> Subject: Re: [TenTec] Eagle 9MHz tap questions.
>>
>> Are you going to add a panadapter ?
>>
>> ================== K8JHR ==================
>>
>>
>> On 12/22/2014 2:46 PM, Rick - DJ0IP / NJ0IP wrote:
>>> Is it just a tap, like perhaps a Y-connection, or does it also have a
>> buffer stage?
>>> Unfortunately my Eagle fell out of the nest before that feature was
>>> added
>> to the radio.
>>> ____________________________________________
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>