[TenTec] Omni VII remoting

[Bob McGraw - K4TAX]

Yes, a standard CAT 5 cable between the radio and router is all that is 
needed.  Then with the router you will have to configure port forwarding for 
5 consecutive ports along with the IP address of the radio.  Then download 
the software OnePlug version 1.12 from the TT website.  With this software 
it will connect to the radio with the ability to control all of the 
functions and have VOIP as well.  Hence oneplug is all that goes to the 
radio.

73
Bob, K4TAX


----- Original Message ----- 
From: "Barry N1EU" <barry.n1eu at gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
Sent: Saturday, July 05, 2014 9:09 AM
Subject: [TenTec] Omni VII remoting


> Could someone please describe what is required to remote the Omni VII? 
> Can
> I cable it directly to my router, open the firewall for its IP, and then
> access it remotely?  What software running remotely will operate it?
>
> Thanks & 73,
> Barry N1EU
>
>
> On Sat, Jul 5, 2014 at 1:57 PM, Bob McGraw - K4TAX <RMcGraw at blomand.net>
> wrote:
>
>> Clearly the release of 1.036 does greatly improve the receiver 
>> performance
>> in regard to noise loading the AGC.  It also improved the internet
>> connectivity to an outstanding level of performance.  I've used my laptop
>> with my cell phone as a "hot spot" and had many very successful QSO's 
>> with
>> the Omni VII connected to the internet.  Even works mobile until I loose
>> cell phone service.
>>
>> The current promotion pricing is simply outstanding and anyone with the
>> slightest opportunity should look into taking advantage of the packages 
>> and
>> attractive pricing.  I do not see this promotion or pricing as or to any
>> degree of negativity with regard to the future of Tentec.
>>
>> Simply it is time for hams to take advantage of the company promotion and
>> allow themselves to obtain some of the best ham equipment available on 
>> the
>> market today.
>>
>> 73
>> Bob, K4TAX
>>
>>
>>
>>
>>
>>
>> ----- Original Message ----- From: "David and Dianne on Comcast" <
>> dhhdeh at comcast.net>
>> To: "Ten Tec Reflector" <tentec at contesting.com>
>> Sent: Friday, July 04, 2014 11:31 AM
>> Subject: [TenTec] Reactions to Omni VII Firmware Revision 1.036 and QRN
>> Generated AGC Swamping?
>>
>>
>>
>>  Hi All,
>>>
>>> Back in May, Ten Tec announced the release of firmware Version 1.036 for
>>> the Omni VII.  Among a number of revisions contained as outlined here by
>>> John Henry on May 28th was "Improved handling of QRN/impulse type noise 
>>> so
>>> it wouldn't prematurely load up AGC."
>>>
>>> I do not recall reading any reactions to this aspect of the 1.036
>>> revision release on this reflector or the Omni VII Yahoo group.
>>>
>>> Last fall I posted here that this AGC issue needed priority improvement
>>> as last summer's QRN here had made the Omni VII's receiver's AGC very
>>> susceptible to QRN initiated swamping. I sold my Omni VII late last fall
>>> primarily because of this issue when it appeared that no resolution was
>>> soon to be forthcoming.
>>>
>>> So, as we are again in QRN season here in MA, I am interested what
>>> improvement in this QRN swamping AGC issue has been realized in V1.036?
>>>
>>> Ten Tec's new Omni VII pricing has me thinking again as I really liked
>>> the Omni VII...but in contrast to my Corsair II, Omni V.9 and my K3, the
>>> Omni VII's QRN swamping issue as it stood last year was not acceptable
>>> here. Has this been fixed?
>>>
>>> Appreciate any of your feedback on or off the reflector.
>>>
>>> 73 de N1LQ-Dave
>>>
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>