[TenTec] Invoking OM7 500 Hz filter ?

[Bob McGraw - K4TAX]

There is no front panel IF Filter manual selection available.

Filter selection is either automatic, thus following the DSP BW when I-F 
FILTER is set to AUTO.
You can select the filter manually via the MENU on the I-F FILTER line.  The 
Multi knob makes this choice from the MENU as it steps through all the 
filter choices.

73
Bob, K4TAX


----- Original Message ----- 
From: <bcarling at cfl.rr.com>
To: "Discussion of Ten-Tec Equipment" <tentec at contesting.com>
Sent: Thursday, July 10, 2014 7:28 PM
Subject: Re: [TenTec] Invoking OM7 500 Hz filter ?


> Thank you. Yes, I read that, and tried it. However, it does not tell me 
> how to select them and
> it didn't switch.
>
> What do I rotate or switch?
>
> Is there any way to customize buttons on the front panel to make one of 
> them select this filter
> without going through the menu every time?
>
> On 10 Jul 2014 at 19:25, Bob McGraw - K4TAX wrote:
>
>> The I-F FILTER line in the MENU will allow you to switch the filter of 
>> your
>> choice manually.
>>
>> 73
>> Bob, K4TAX
>>
>>
>> ----- Original Message ----- 
>> From: <bcarling at cfl.rr.com>
>> To: <tentec at contesting.com>
>> Sent: Thursday, July 10, 2014 7:17 PM
>> Subject: Re: [TenTec] Invoking OM7 500 Hz filter ?
>>
>>
>> > Thank you Bob. I already did all that. And yes, it is already set to
>> > AUTIO.
>> >
>> > I simply want to know how to switch it on and off when I am operating 
>> > the
>> > radio. I thought I
>> > made that clear.
>> >
>> > "Does anyone know how to invoke the 500 Hz Collins filter once it is
>> > installed and enabled?"
>> >
>> >
>> > On 10 Jul 2014 at 19:06, Bob McGraw - K4TAX wrote:
>> >
>> >> Go to the MENU. Scroll to the bottom.  Set ENABLE 500 Hz to YES.  And 
>> >> if
>> >> you
>> >> have the 300 Hz filter do the same for that one.  Then at the line I-F
>> >> FILTER select AUTO.
>> >>
>> >> 73
>> >> Bob, K4TAX
>> >>
>> >>
>> >> ----- Original Message ----- 
>> >> From: <bcarling at cfl.rr.com>
>> >> To: <tentec at contesting.com>
>> >> Sent: Thursday, July 10, 2014 6:42 PM
>> >> Subject: [TenTec] Invoking OM7 500 Hz filter ?
>> >>
>> >>
>> >> > Hello,
>> >> >
>> >> > I now have a clean sounding OMNI VII after doing a master reset. 
>> >> > Thanks
>> >> > guys.
>> >> >
>> >> > Does anyone know how to invoke the 500 Hz Collins filter once it is
>> >> > installed and enabled?
>> >> >
>> >> > I have read the manual through twice and still can't figure out how 
>> >> > to
>> >> > switch from 2.5 kHz
>> >> > filter to 500 Hz !!  Maybe I am not too smart. The book seems to 
>> >> > dance
>> >> > all
>> >> > around the topic
>> >> > but never tell you how!
>> >> >
>> >> > 73 - Brian, AF4K
>> >> >
>> >> > Brian Carling, Radio AF4K
>> >> > _______________________________________________
>> >> > TenTec mailing list
>> >> > TenTec at contesting.com
>> >> > http://lists.contesting.com/mailman/listinfo/tentec
>> >> >
>> >>
>> >>
>> >
>> >
>> > Brian Carling, Radio AF4K
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec at contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>> >
>>
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>