[TenTec] Scout has vy low Pwr out on some bands

[Rick - DJ0IP / NJ0IP]

You can't get an eraser down inside the barrel.
It is less than a quarter inch wide and very long.

I used a soft eraser on all the other pins but it won't work on that barrel
connector.

73 - Rick, DJ0IP
(Nr. Frankfurt am Main)


-----Original Message-----
From: TenTec [mailto:tentec-bounces at contesting.com] On Behalf Of Froiseth
Richard
Sent: Thursday, July 17, 2014 3:17 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Scout has vy low Pwr out on some bands

I will my two cents worth. maybe it will help.
I don't know if this will work with this application, but a Staedtler eraser
(white eraser) works very well on cleaning gold contacts.  I used this
method to clean the contacts on plug in boards.  Just be careful of the
excess, but it shines up the gold contacts very nicely.


73's
Rich, WD6DOK







On Jul 16, 2014, at 6:47 PM, ken.d.brown at hawaiiantel.net wrote:

> 
> 
> I did not work for Tektronix. I worked for an independent calibration 
> lab called "Intertyme Metrology Laboratory." I serviced a lot of Tek 
> 547, 544, 535, and various plug-ins for them like 1A4, 1A2 and other 
> specialty vertical plug-ins. 465, 485. There was also a Tek scope that 
> IBM had a lot of, I don't remember the number. It was built in the 
> style of a 547, but a bit smaller and had plug-ins for both vertical 
> and horizontal, a rectangular CRT. I worked on some 7400 series scopes
too.
> Also some HP scopes, 182 C. I did not like Hewlett Packard o'scopes 
> very much. Nothing could compare to a Tektronix scope. HP for signal 
> generators, Tek for scopes would be my preference.
> 
> 73 DE N6KB
> 
> On 2014-07-16 12:07, Rick - DJ0IP / NJ0IP wrote: 
> 
>> Ha, so we do have a common past.
>> 
>> Actually we were Tektronix.
>> We had the exclusive distributorship for Germany for over 30 years.
>> We were treated just like TEK employees. Same training, etc.
>> In fact I am still a member of the Tektronix ham radio club which 
>> consists of all hams that ever worked for Tektronix.
>> 
>> 73 - Rick, DJ0IP
>> (Nr. Frankfurt am Main)
>> 
>> -----Original Message-----
>> From: TenTec [mailto:tentec-bounces at contesting.com] On Behalf Of Ken 
>> Brown
>> Sent: Wednesday, July 16, 2014 9:47 AM
>> To: Discussion of Ten-Tec Equipment
>> Subject: Re: [TenTec] Scout has vy low Pwr out on some bands
>> 
>>> This is the way we cleaned contacts when I worked for Rhode und 
>>> Schwarz in
>> the 70s, repairing Tektronix oscilloscopes.
>> 
>> This brings back memories, as I used to repair and calibrate 
>> Tektronix oscilloscopes in the '70s too. Our procedure was to rinse 
>> them (the whole
>> scope) with deionized water. Wash them with a solution of water and a 
>> product called "Kelite." Some sort of detergent from Allied Chemical, 
>> rinse them with DI water again, and put them in a drying oven for about a
week.
>> When we got them out of the oven we carefully applied
>> WD40 to every switch contact and connector using a small paintbrush. 
>> We absolutely did not spray WD40 on anything. It was applied 
>> carefully only to the contacts and the positioning ball/spring thing 
>> in rotary switches, also the wipers on potentiometers. I suspect that 
>> DeOxit or Cramolin would have been better than WD40, but WD40 is what 
>> we used. I'm pretty sure we were following Tektronix recommended
procedures.
>> 
>>> The Q-Tip is a good idea. The problem is, the entire plug is very 
>>> narrow
>> but long. It's hard to get down in there.
>>> A Q-tip is probably the best bet.
>> 
>> I suggest that a small paintbrush may be a better option than a Q-Tip. 
>> The cotton fibers of a Q-Tip could catch on something and be left 
>> behind on the contact. I think with a tiny paint brush you have less 
>> chance of leaving a bristle behind.
>> 
>> DE N6KB
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec [1]
>> 
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec [1]
> 
> 
> Links:
> ------
> [1] http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec at contesting.com
http://lists.contesting.com/mailman/listinfo/tentec