[TenTec] Using a Mac to install OMNI VII firmware

[Silevitch, Michael]

I was afraid of that, Pepe!

Regards
  Michael 

Sent from my iPhone

> On May 10, 2015, at 3:55 PM, José Félix Ballester <jfballester at gmail.com> wrote:
> 
> I found it to be just that -trial and error- adding to the pain...
> 73 de Pepe WP3HW
> 
> Sent from my iPhone
> 
>> On May 10, 2015, at 12:58 PM, Silevitch, Michael <m.silevitch at neu.edu> wrote:
>> 
>> Thanks to all of you who responded. I've come to the same conclusion, which is either a dedicated PC or using the Mac in virtual machine or Windows boot mode. The only question is the linkage between the serial to USB adapter and the COM port assignment. Most likely this will be trial and error. 
>> 
>> Regards
>>   Michael K1PEV
>> 
>> Sent from my iPad
>> 
>>> On May 10, 2015, at 12:54 PM, Duane Calvin <ac5aa1 at gmail.com> wrote:
>>> 
>>> Have a friend with a Windows laptop?  Just work out a swap - three fingers
>>> of Redeye for a few minutes to install!  :-)
>>> 
>>>  73, Duane
>>> 
>>> Duane Calvin, AC5AA
>>> Austin, Texas
>>> www.ac5aa.com  
>>> 
>>> 
>>> 
>>> 
>>> -----Original Message-----
>>> From: TenTec [mailto:tentec-bounces at contesting.com] On Behalf Of denton
>>> sprague
>>> Sent: Sunday, May 10, 2015 11:37 AM
>>> To: Clayton Brantley; Discussion of Ten-Tec Equipment
>>> Subject: Re: [TenTec] Using a Mac to install OMNI VII firmware
>>> 
>>> Sad to say, but there is still very little ham software available for Macs.
>>> For now the only apparent alternative is to keep a dedicated windoze pc
>>> available for ham software use.
>>> 
>>> 
>>> On May 10, 2015, at 9:24 AM, Clayton Bra4P via TenTec
>>> <tentec at contesting.com> wrote:
>>> 
>>>> I thought the Mac wouldn't work. 
>>>> 
>>>> Clayton N4EV
>>>> 
>>>>   From: Mike Bryce <prosolar at sssnet.com>
>>>> To: Clayton Brantley <clayton_n4ev at yahoo.com>; Discussion of Ten-Tec
>>> Equipment <tentec at contesting.com> 
>>>> Sent: Sunday, May 10, 2015 12:14 PM
>>>> Subject: Re: [TenTec] Using a Mac to install OMNI VII firmware
>>>> 
>>>> Sorry to say, the mac's won't work. UNLESS you run "Parallels" a windows
>>> emulator
>>>> 
>>>> Mike, WB8VGE
>>>> SunLight Energy Systems
>>>> The Heathkit Shop
>>>> http://www.theheathkitshop.com/ <http://www.theheathkitshop.com/>
>>>> J e e p
>>>> o|||||||o 
>>>> 
>>>> A man with one clock knows what time it is. A man with two clocks is never
>>> sure. 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>>> On May 10, 2015, at 11:39 AM, Clayton Brantley via TenTec
>>> <tentec at contesting.com> wrote:
>>>>> 
>>>>> You might check with the guys in Sevierville, but I don't think the
>>> updates will work with anythingBUT a Windows PC.  I use Linux as my main
>>> computer but I keep a PC around for what you aretaking about.
>>>>> Clayton N4EV
>>>>> 
>>>>>    From: "Silevitch, Michael" <m.silevitch at neu.edu>
>>>>> To: "TenTec at contesting.com" <TenTec at contesting.com> 
>>>>> Sent: Sunday, May 10, 2015 8:14 AM
>>>>> Subject: [TenTec] Using a Mac to install OMNI VII firmware
>>>>> 
>>>>> I have just purchased an OMNI VII and will be updating the firmware. I
>>> would prefer to use my Mac computer rather than a PC for this. I have a
>>> serial to USB adapter which should work to connect the OMNI to the Mac (or
>>> PC for that matter.) Any guidance would be appreciated. 
>>>>> 
>>>>> I may also want to operate the OMNI remotely using a Mac rather than a
>>> PC. Again any advice would be appreciated. 
>>>> 
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec at contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>> 
>>>> 
>>>> 
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec at contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>> 
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>> 
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec