[TenTec] Omni VI + Voice Synthesizer Board.

[Carl Winkles]

Here is what Ten Tec told me years ago: "If there is a diode just to the left of the MC74HC573 chip (third connection on the left edge of the card) place a jumper across it. Depending on the model of the rig, there will be one diode, two diodes or a jumper. The Omni series requires a jumper for proper readout. '

I don't remember having any problem doing this, and I remember that it worked.  Hope this helps. 

Carl, K4SEV

Enviado desde mi iPhone

> El mar 9, 2016, a las 1:56 AM, Froiseth Richard <Rfwd6dok at centurylink.net> escribió:
> 
> Mike,
> 
> Thanks for responding to my question.
> I bought the Omni VI + from Ten Tec a few years ago and the radio came with the board installed.
> There were some things going on in my life at that time and I didn’t have a chance to check out the board or the rest of the radio.  I know that sounds silly, but that's what happened, anyway do you know if you can tell if the mod has been done by looking at the board? There is a note in the manual stating if the board came out of anything other than a 563 or 564 call the factory for modification details.  I guess I can shoot them off an e-mail and hope they respond.
> I was hoping that someone on here could answer my question.
> 
> 
> 73’s
> Rich, WD6DOK
> 
> 
> 
> 
> 
> 
> 
>> On Mar 8, 2016, at 6:25 PM, Mike Bryce <prosolar at sssnet.com> wrote:
>> 
>> silly question, but did this start to act up or did you buy a voice card and add it to the radio?
>> 
>> There is a modification that needs to be done to the card if it came out of the paragon and into the Omni V/VI. I don’t recall what it was, but it was rather simple
>> 
>> mike, wb8vge
>> 
>> 
>> Mike, WB8VGE
>> SunLight Energy Systems
>> The Heathkit Shop
>> http://www.theheathkitshop.com/ <http://www.theheathkitshop.com/>
>> J e e p
>> o|||||||o 
>> 
>> A man with one clock knows what time it is. A man with two clocks is never sure. 
>> 
>> 
>> 
>>> On Mar 8, 2016, at 4:45 PM, Froiseth Richard <rfwd6dok at centurylink.net> wrote:
>>> 
>>> I have an Omni VI + with the Voice Synthesizer Board #257 installed.
>>> When I press the voice button on the front of the radio the voice announces the following:
>>> 
>>> 80m, 40m announces 29731 no matter where you are tuned.
>>> 12m, 15m and 20m announces 429731 no matter where you are tuned.
>>> 
>>> My understanding is the board should announce the freq. you are presently tuned.
>>> 
>>> Can anyone shed some light on this problem?
>>> 
>>> 73’s
>>> Rich, WD6DOK
>>> 
>>> 
>>> 
>>> 
>>> 
>>> 
>>> 
>>>> On Mar 2, 2016, at 5:09 PM, Barry N1EU <barry.n1eu at gmail.com> wrote:
>>>> 
>>>> Don't use the 500hz and 250hz filters.  Put an Inrad #762 600hz filter in
>>>> the 1000hz slot: http://users.vnet.net/btippett/inrad_.htm
>>>> 
>>>> 73, Barry N1EU
>>>> 
>>>>> On Wed, Mar 2, 2016 at 11:57 PM, Tim Wininger <ky5rtim at gmail.com> wrote:
>>>>> 
>>>>> Anyone have one or all of these filters excess to your needs. Looking for
>>>>> the TT versions or Inrad versions.
>>>>> 
>>>>> Thanks for any info,
>>>>> 
>>>>> Tim , AB4B
>>>>> Rogersville ,AL
>>>>>     35652
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec at contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec at contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>> 
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> 
>> _______________________________________________
>> TenTec mailing list
>> TenTec at contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> 
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec