[TenTec] I surrender

[Lee]

Joe,

The Omni VI works fine with Winlink Winmor.  I have one here that I have 
used many times.

I assume MMTTY and fldigi are being used with the Omni.  If so, then we 
know the hardware interface works so it is only a configuration issue 
with Winlink.  What do you use for an interface between your computer 
and the Omni?  In Winlink there are two setup screens that need 
attention,  "WINMOR TNC setup" and "Radio Setup".   TNC setup selects 
the sound card interface and Radio Setup selects radio control if used 
(yours appears to be working fine) and PPT control.

Can you look at the MMTTY or fldigi setup parameters to get an idea of 
what works?

73,

-Lee-

WA3FIY

Sounds like the PTT line to the Omni is not getting triggered.
------ Original Message ------
From: "Joe Papworth via TenTec" <tentec at contesting.com>
To: n4py3 at earthlink.net
Cc: k8mp at aol.com; tentec at contesting.com
Sent: 3/4/2018 8:12:21 AM
Subject: Re: [TenTec] I surrender

>Hmmm...
>I run MMTTY and FLFigi on that same PC over the same connection and 
>they key the Omni VI Plus fine.
>
>Those work but WinLink/Winmor does not, so it's gotta be something in 
>the program or a setting in it.
>
>Later, Joe, K8MP
>
>Sent from AOL Mobile Mail
>
>
>-----Original Message-----
>From: Carl Moreschi <n4py3 at earthlink.net>
>To: k8mp <k8mp at aol.com>
>Cc: tentec <tentec at contesting.com>
>Sent: Sun, Mar 4, 2018 06:54 AM
>Subject: Re: [TenTec] I surrender
>
>
>I don't think the Omni VI implemented that command.
>
>Carl Moreschi N4PY
>58 Hogwood Rd
>Louisburg, NC 27549
><a href="http://www.n4py.com" target="_blank">www.n4py.com</a>
>
>On 3/4/2018 12:06 AM, <a href="mailto:k8mp at aol.com">k8mp at aol.com</a> 
>wrote:
>>  They're talkin' Carl. The rig accepts the mode and QRG commands from 
>>the
>>  PC but apparently it doesn't accept the command to xmit.
>>
>>
>>  Sent from AOL Mobile Mail
>>
>>
>>  -----Original Message-----
>>  From: Carl Moreschi <<a 
>>href="mailto:n4py3 at earthlink.net">n4py3 at earthlink.net</a>>
>>  To: Discussion of Ten-Tec Equipment <<a 
>>href="mailto:tentec at contesting.com">tentec at contesting.com</a>>
>>  Sent: Sat, Mar 3, 2018 11:12 PM
>>  Subject: Re: [TenTec] I surrender
>>
>>
>>  There's 3 things that have to match.
>>
>>  Baud rate (probably 1200 but might not be )
>>  CIV address (should be 04 )
>>  Correct comport number.
>>
>>  If all those match it will work.
>>
>>  Carl Moreschi N4PY
>>  58 Hogwood Rd
>>  Louisburg, NC 27549
>>  <a href="http://www.n4py.com" target="_blank">www.n4py.com</a> <<a 
>>href="http://www.n4py.com" target="_blank">http://www.n4py.com</a>>
>>
>>  On 3/3/2018 10:32 PM, Joe Papworth via TenTec wrote:
>>   > Gents,
>>   >
>>   > <div>I threw in the towel on making WinLink and Winmor work with 
>>my
>>  Omni VI Plus. I have WinLink working over our local Mesh network and 
>>I
>>  was hoping get it working on HF but no dice.
>>   >
>>   > Thank you Carl, Rod, Greg, and others who weighed in.
>>   >
>>   > Joe, K8MP
>>   >
>>   > Sent from AOL Mobile Mail</div>
>>   > _______________________________________________
>>   > TenTec mailing list
>>   > <a href="mailto:TenTec at contesting.com">TenTec at contesting.com</a> 
>><<a 
>>href="mailto:TenTec at contesting.com?">mailto:TenTec at contesting.com</a>>
>>   > <a href="http://lists.contesting.com/mailman/listinfo/tentec" 
>>target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>>   >
>>  _______________________________________________
>>  TenTec mailing list
>>  <a href="mailto:TenTec at contesting.com">TenTec at contesting.com</a> <<a 
>>href="mailto:TenTec at contesting.com?">mailto:TenTec at contesting.com</a>>
>>  <a href="http://lists.contesting.com/mailman/listinfo/tentec" 
>>target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>_______________________________________________
>TenTec mailing list
>TenTec at contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec