[TenTec] I surrender

[Stan Gammons]

Are you using PTT to key the rig with fldigi?   With WSJT-X, I've tried 
using CAT with my Omni VI and I can't get it to work right. It will key 
the rig when I select "test CAT"  but it won't unkey until I close the 
program.  Maybe Winlink is trying to use CAT and should be using PTT?   
I use the default CIV address of 04, 19200 for the baud rate and a home 
made computer interface which key the rig when RTS goes high.

hth

73

Stan
KM4HQE


On 03/04/2018 07:12 AM, Joe Papworth via TenTec wrote:
> Hmmm...
> I run MMTTY and FLFigi on that same PC over the same connection and they key the Omni VI Plus fine.
>
> Those work but WinLink/Winmor does not, so it's gotta be something in the program or a setting in it.
>
> Later, Joe, K8MP
>
> Sent from AOL Mobile Mail
>
>
> -----Original Message-----
> From: Carl Moreschi <n4py3 at earthlink.net>
> To: k8mp <k8mp at aol.com>
> Cc: tentec <tentec at contesting.com>
> Sent: Sun, Mar 4, 2018 06:54 AM
> Subject: Re: [TenTec] I surrender
>
>
> I don't think the Omni VI implemented that command.
>
> Carl Moreschi N4PY
> 58 Hogwood Rd
> Louisburg, NC 27549
> <a href="http://www.n4py.com" target="_blank">www.n4py.com</a>
>
> On 3/4/2018 12:06 AM, <a href="mailto:k8mp at aol.com">k8mp at aol.com</a> wrote:
>> They're talkin' Carl. The rig accepts the mode and QRG commands from the
>> PC but apparently it doesn't accept the command to xmit.
>>
>>
>> Sent from AOL Mobile Mail
>>
>>
>> -----Original Message-----
>> From: Carl Moreschi <<a href="mailto:n4py3 at earthlink.net">n4py3 at earthlink.net</a>>
>> To: Discussion of Ten-Tec Equipment <<a href="mailto:tentec at contesting.com">tentec at contesting.com</a>>
>> Sent: Sat, Mar 3, 2018 11:12 PM
>> Subject: Re: [TenTec] I surrender
>>
>>
>> There's 3 things that have to match.
>>
>> Baud rate (probably 1200 but might not be )
>> CIV address (should be 04 )
>> Correct comport number.
>>
>> If all those match it will work.
>>
>> Carl Moreschi N4PY
>> 58 Hogwood Rd
>> Louisburg, NC 27549
>> <a href="http://www.n4py.com" target="_blank">www.n4py.com</a> <<a href="http://www.n4py.com" target="_blank">http://www.n4py.com</a>>
>>
>> On 3/3/2018 10:32 PM, Joe Papworth via TenTec wrote:
>>   > Gents,
>>   >
>>   > <div>I threw in the towel on making WinLink and Winmor work with my
>> Omni VI Plus. I have WinLink working over our local Mesh network and I
>> was hoping get it working on HF but no dice.
>>   >
>>   > Thank you Carl, Rod, Greg, and others who weighed in.
>>   >
>>   > Joe, K8MP
>>   >
>>   > Sent from AOL Mobile Mail</div>
>>   > _______________________________________________
>>   > TenTec mailing list
>>   > <a href="mailto:TenTec at contesting.com">TenTec at contesting.com</a> <<a href="mailto:TenTec at contesting.com?">mailto:TenTec at contesting.com</a>>
>>   > <a href="http://lists.contesting.com/mailman/listinfo/tentec" target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>>   >
>> _______________________________________________
>> TenTec mailing list
>> <a href="mailto:TenTec at contesting.com">TenTec at contesting.com</a> <<a href="mailto:TenTec at contesting.com?">mailto:TenTec at contesting.com</a>>
>> <a href="http://lists.contesting.com/mailman/listinfo/tentec" target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec