[TenTec] Argonaut 509 - PTO rebuild parts/instructions needed - still possible? advice/recommendations?

[Bob McGraw K4TAX]

There is a dedicated Tentec Argonaut site found at: 
https://groups.io/g/TEN-TEC-Classic-Argonauts.   You may find more or 
dedicated information on this site.

73

Bob, K4TAX


On 11/21/2020 12:11 AM, wb0gaz via TenTec wrote:
>   Found that I had the ten-tec instructions in my file, so proceeded up to a point where I am stuck, so looking for advice:
>
> PTO subassembly housing (that holds the coil and movable parts) removed from the 509 Argonaut without difficulty; all of the various small parts are stashed in small plastic bags.
>
> (referring to the ten-tec instructions on PTO rebuild)
>
> "Step 4. Push tuning shaft (J) back far enough to remove stop pin (H) using long nose pliers. Note the position of this pin as it must be put back in the same hole."
>
> I am not able to push the tuning shaft (J) back (I presume by back, they mean push on it towards the rear of the radio) very far at all - certainly not enough to expose the stop pin so I can safely remove it (I assume the idea is to push the shaft back towards the rear until the stop pin is clear of housing so that the stop pin can be removed.)
>
> The small-diameter inner shaft (where the PTO knob is attached) turns normally, but no movement is transmitted to the gear-reduced larger-diameter outer shaft (where the kHz ring and string wind-up goes), which I think is what actuates the PTO movement forward and backward for frequency change.
>
> As far as I can tell, the root problem is that the "core drive rod (K)" - which is the larger-diameter shaft just behind where the PTO knob is attached - does not turn at all (certainly not by hand, and I've not tried using any tool to turn it because it seems very unwilling to rotate.) Turning this is necessary at step 7 so it can be removed from the assembly housing. I can't work out why it does not turn. What grease I've cleaned up so far seems normal consistency.
>
> I can press the tuning shaft (J) in maybe 1/8", and I see the three ball bearings move back in their plastic housing, but they're not exposed enough to remove them.
>
> Does this ring a bell with anyone? I'm stumped!
>
> Thanks,
>
> 73 Dave WB0GAZ wb0gaz at yahoo.com
>
>
>
>       On Friday, November 20, 2020, 08:06:37 PM MST, <wb0gaz at yahoo.com> wrote:
>   
>    My Argonaut 509 (S/N 509-3xxx) has been in storage for a long time, and after unpacking it and putting it in line, I discovered the PTO (frequency dial, not the resonator rack) control is largely immobile. I suspect the PTO mechanism grease has gone bad and I'd need to remove the PTO, disassemble, remove the old grease, apply new grease, reassemble, re-install and realign.
>
> All that said, the last time I did this (for another PTO-based analog Ten-Tec transceiver) was some years ago and Ten-Tec at the time could supply the needed materials and instructions.
>
> I presume with Ten-Tec gone that I'm "on my own", so looking here for any advice as to how to proceed. I no longer have the materials (I recall a kind of green grease and a very small metal part) nor instructions (a few photocopied pages, which served well the last time I did this years ago.)
>
> The 509 seems otherwise to be in good shape, it's just stuck at xx.060 MHz or thereabouts.
>
> Thanks for any suggestions!
>
> 73 Dave WB0GAZ wb0gaz at yahoo.com
>
>      
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>