[TenTec] hex set screw size for Century 22

Garry Nichols garrnich at gmail.com
Sun Oct 23 17:42:37 EDT 2022


Thank you again, Andrew!  Evidence is certainly pointing to 0.05"!

I have not run into a hex key that small before.  Both True Value and Ace
carry keys in that size, but I need to buy a small set to get it.  Under
$10.  Ace carries Elkind brand which claims to be an old US hex key
manufacturer.  True Value has Elkind and their own Master Mechanic which is
probably Chinese.

Garry

On Sun, Oct 23, 2022 at 5:09 PM Andrew Moore <andrew.nv1b at gmail.com> wrote:

> Hi Garry - I just happened to watch a video on the Ten-Tec Jupiter and
> found that it too uses a 0.050 hex set screw. Probably a safe bet, though
> not a guarantee, that Ten-Tec standardized on this size. Let us know how
> you make out.
>
> 73/72 de NV1B
> ..
>
>
>
> On Fri, Oct 21, 2022 at 5:48 PM Garry Nichols <garrnich at gmail.com> wrote:
>
> > Hello Andrew!  A pleasant surprise and "small world" (of us Ten-Tec
> > fans?).
> >
> > I spoke to my local hardware store today and the smallest they had was --
> > 0.05 inches!  So I think we have a "bingo".  I thought it unlikely that
> > Ten-Tec was using metric back in the first half of the 80s.
> >
> > I tried to measure the set screw with a mm rule and a magnifying glass
> but
> > my ruler had fairly thick tick marks.  I see that 1mm converts to 0.04
> > inches so I'm in the ballpark.
> >
> > TU ES 72!
> >
> > Garry WA1GWH
> >
> >
> >
> > On Fri, Oct 21, 2022 at 4:51 PM Andrew Moore <andrew.nv1b at gmail.com>
> > wrote:
> >
> > > Hi Garry -
> > >
> > > Not sure if the C22 uses the same size as the Corsair II, but it seems
> > > possible. The Corsair II uses a 0.050 inch hexagonal screw.
> > >
> > > Thanks for the QSO yesterday and for trying to pull my 2 watts out of
> the
> > > noise. I was using the K2, but hope to be on the Corsair II soon - it's
> > > currently on the bench with a TX issue to fix.
> > >
> > > 73/73,
> > > Andrew NV1B
> > > ..
> > >
> > >
> > > On Fri, Oct 21, 2022 at 3:47 PM Garry Nichols <garrnich at gmail.com>
> > wrote:
> > >
> > > > Does anyone know what size the tiny set screws that hold the knobs on
> > > are?
> > > > They measure about 1 mm for the hex opening but that is an estimate.
> > > >
> > > > My rig is #666 in case there was a change across the production run.
> > > >
> > > > Are they metric or English?
> > > >
> > > > TU,
> > > >
> > > > Garry WA1GWH
> > > > near Syracuse, NY
> > > > _______________________________________________
> > > > TenTec mailing list
> > > > TenTec at contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/tentec
> > > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec at contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > _______________________________________________
> > TenTec mailing list
> > TenTec at contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> _______________________________________________
> TenTec mailing list
> TenTec at contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>


More information about the TenTec mailing list