[TowerTalk] [SPAM] Re: Cutting 3/16" EHS...

[Jim Walker]

 I purchased the 18 inch bolt cutters from Harbor Freight.  It gives one
pause to reflect upon the old adage, "you get what you pay for."

The Harbor Freight cutters lasted through approximately 10 - 15 clean cuts
of 3/16 EHS after which it would only cut half or less of the individual
woven strands.

No amount of adjustment would bring them back to where they would cut 3/16
inch with a single cut.  I still have them, but will ship them free to
anyone who wants to pay for shipping.  :-)

YMMV,

Jim
KB0X

-----Original Message-----
From: towertalk-bounces at contesting.com
[mailto:towertalk-bounces at contesting.com] On Behalf Of Chet Moore
Sent: Sunday, December 03, 2006 8:36 AM
To: K8RI on TowerTalk; towertalk at contesting.com
Subject: [SPAM] Re: [TowerTalk] Cutting 3/16" EHS...

I don't do a lot of cutting EHS but  Harbor freight has the 24 inch on sale
right now for  $9.99.  the 36 inch  version is $18.00

73

Chet N6ZO
----- Original Message -----
From: "K8RI on TowerTalk" <K8RI-on-TowerTalk at tm.net>
To: <towertalk at contesting.com>
Sent: December 03, 2006 2:54 AM
Subject: Re: [TowerTalk] Cutting 3/16" EHS...


> <snip>
>>
>> I looked for and found the bolt cutters.  The 24" HK Porter cutter was 
>> $50
>> and the 18" was $20.  I had a 3" piece of EHS with me and the salesman 
>> let
>> me try cutting the piece with the 18" cutter.  One try and the EHS was 2
>> pieces of EHS.  Fortunately, I was close to and faced a corner when I cut
>
> Reallllyyyy go...don't they? When cutting the end off you really only have
> the short piece to worry about unless they are both short.  In the 
> cut-off,
> or chop saw the cable is clamped in place.
>
>> the EHS because both pieces shot out and into the display cases and
>> bounced
>> to the floor--out in the open, they could have gone some distance and
>> possibly hit someone--lesson learned there...  Neither of us was 
>> expecting
>> that.
>>
>
> The guy selling bolt cutters should have known, but that happens in the 
> big
> box stores at times. Course it happens with new people in the hardware
> stores too.
>
>> Anyway, I bought the 18" cutters and 30 minutes after getting home,
>> measuring out and marking the cut points I wanted to make, the job was
>> done.
>
> I'm getting older. I prefer the 24" <:-))
>
>>
>>
>> $20 well spent.
>
> Ain't it nice with the proper tools?  <:-))
>
> I'm still waiting for my loos gage to tighten the guys.   I'm going to be
> lower ihtm and that is going to require cutting EHS "tails" to go between
> the turnbuckles and the Phyllistran.
> Roger Halstead (K8RI and ARRL 40 year Life Member)
> N833R - World's oldest Debonair CD-2
> www.rogerhalstead.com
>
>>
>>
>> 73,
>> Dale, kg5u
>>
>>
>>
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk at contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> 


_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk at contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk