[TowerTalk] And now for something completely different(TrueNorth)

Jim Lux jimlux at earthlink.net
Mon Sep 18 01:04:35 EDT 2006


At 04:07 PM 9/17/2006, K8RI on TowerTalk wrote:

>----- Original Message -----
>From: "Jim Lux" <jimlux at earthlink.net>
>To: "K8RI on TowerTalk" <K8RI-on-TowerTalk at tm.net>;
><towertalk at contesting.com>
>Sent: Sunday, September 17, 2006 6:14 PM
>Subject: Re: [TowerTalk] And now for something completely
>different(TrueNorth)
>
>
><snip>>
> > Come on, Roger, you need a better antenna.. Let's see.. f/10 at 2500mm
> > means you've got 250mm aperture, at lambda of say 500 nm, or 500 lambda.
> > So, on 20m, you only need an antenna with an aperture of, let's see, 10
> > km. But... real hams work on top band, so you'd
>
>So this translates into a boom length on my tri-bander to about the same
>although we might have to add a few elements due to spacing.  But given
>about the same figures I'd need about a 10 km boom length or about 6.2
>miles.  That sorta adds a new meaning to "boom truss" doesn't it? <:-))
>
>Let's see. Figuring it's center mounted for simplicity, the boom would
>extend 3.1 miles or 5 km from the rotator.  A typical rotator for a
>tribander runs about 1 RPM while the bigger stuff is 1/2 RPM. So giving it
>the benefit of the doubt and running 1/2 RPM  Knowing the diameter is 10 km
>and the circumference is pi * d the circumference is 31.14159 km or about
>9.7 miles. So with the slower rotator "for the big stuff" the ends of the
>boom have to travel 9.7 miles in 2 minutes or 4.8 6 miles in one minute.  We
>know a mile a minute is 60 mph so 60 * 4.8 gives us boom tip speeds of 292
>mph or 471 km/h. Spose maybe we need to ramp up the rotator speed instead of
>just starting to turn?  Other wise we may get a bit of lag between what the
>rotator does and what the ends of the antenna do.  I guess this means a
>suspension system and a bit heavier/stronger boom and elements are going to
>be needed.  OTOH...How many individual tri-banders would it take in a phased
>array to get the same arpeture? I can see I may have to order a bit of extra
>coax too. OTOH as I can only go 1500 watts PEP total into the antennas I
>could get by with some very inexpensive milliwatt transmitters at each
>antenna. Now the main thing left is how to account for path variations over
>the entire array besides the phasing.

Details are an exercise for the reader.  But realistically, this is 
the way of the future. As computational power gets cheaper, phased 
arrays start to look more attractive.  If nothing else, spatial 
combining is less lossy than the various combiners used in current 
solid state amps (excepting the new THP kilowatt widget). (and 
nothing beats a single big tube)


> > need about 100 km. (hmm, you'd have trouble at Field day.. everything has
> > to fit in a 1000 ft circle.) This is up in LOFAR antenna territory.
> >
>Oh! Wait...That means I'm going to have to prune the boom a bit and we've
>dropped the boom tip speed down to a bit above 30 MPH at one rpm.  I went
>with the faster speed as we've shortened the boom so much.
>
>Still with the phased array approach using one wavelength spacing between
>antennas we could put up 14 + 1 across that 1000 foot circle.  Too bad they
>didn't make it a rectangle a 1000 feet on a side.

Don't forget you have unlimited dimensions in the vertical 
direction.  And, unlike a reflector (mirror) , you can get aperture 
in both directions: normal and crossways.

>  The we could put up 15^2
>or 225 tri-banders and it's only 6.66 watts to each at the feed point. So if
>we use fiber optics with active phase delay to and from the main control
>point the phasing becomes relatively simple and I don't need all that extra
>coax.
>
>Hmmm... It's not nearly so difficult to reach astronomical precision at HF
>as I thought<:-)) Iwonder who I can get to construct the 225 way power
>divider. I gave up trying to calculate how much coax it'd take let alone the
>continuously variable phasing as the antennas are turned as with the fiber
>it's just cut and fit with active delays.  This stuff is getting simpler by
>the minute.

Even easier.. you send the same signal to all the elements, and just 
have a digital delay at the element that adjusts appropriately. You 
need an accurate time/phase reference at the element, but that's 
fairly easy too, these days.

not only that, but it's been done (albeit at a different frequency).. 
Bernie Steinberg's Radio Camera is an example.



> >><snip>
> >
> >
> >
> >>These are two different realms with far different requirments. Applying
> >>the
> >>far greater astronomical precision requirements to antenna alignment hurts
> >>nothing, but gains nothing as well. OTOH is good experience<:-))
> >
> > I think everyone should try several alignment methods.. not just for their
> > antenna, but just because it's fun and not particularly time consuming.
> > Especially the "stick and shadow" approaches.  It's easy to say, "mark
> > when the shadow is shortest".. much tougher to actually do it.
>
>Being able to determine *when* the shadow is shortest is an art. If we took
>10 hams (myself included) I wonder how close we could each determine local
>"noon" and how much variation we'd have.  Personally, I don't think I'd do
>very well as I've not done that sort of exercise in a long time.
>Knowing the time of local noon should give us our longitude. How close can
>you come to matching my GPS?

Not very.. at least not with a stick and shadow. If you let me use a 
radio receiver for WWV, I could do a bit better, but 10 meter 
accuracy? It's that whole accurate clock thing.





More information about the TowerTalk mailing list