[TowerTalk] Fw: Need help identifying an old tri-bander

[Bill Aycock]

-----Original Message----- 
From: Bill Aycock
Sent: Monday, January 17, 2011 8:50 PM
To: Jim W7RY
Subject: Re: [TowerTalk] Need help identifying an old tri-bander

I have an ATB-34, and I just checked some dimensions. It is puzzling,
because the driven element and reflector are almost on, but the Boom is 67"
longer than on the ATB-34 (~211"). I can check some more, if there is a
chance he extended it.
Bill--W4BSG

-----Original Message----- 
From: Jim W7RY
Sent: Sunday, January 16, 2011 10:23 PM
To: N6FD ; Tower Talk
Subject: Re: [TowerTalk] Need help identifying an old tri-bander

Sounds like a Cushcraft ATB-34. They were just discussed at length here on
the reflector. Including a link for the manual.

Do a search at the tower talk archives and the manual link should pop up. Or
Google ATB-34 and you'll probably find it.

73
Jim W7RY


--------------------------------------------------
From: "N6FD" <n6fd at hughes.net>
Sent: Sunday, January 16, 2011 8:05 PM
To: "Tower Talk" <towertalk at contesting.com>
Subject: [TowerTalk] Need help identifying an old  tri-bander

> I bought a tri-bander used from a silent key's estate.  His wife did not
> have any documentation for the antenna.  Given the state of the antenna
> and the tower that I got with it, it was probably put up some time in
> the 70's or 80's.  No markings have survived on the antenna. The
> following are the details of the antenna.  I don't have the original
> spacing between the elements.
>
> Boom length:  278 inches, in three sections
> Reflector: 382 inches with one set of traps
> Driven element:  317 inches with two sets of traps, center insulated,
> fed with balun
> Director 1:  209 inches, no traps
> Director 2:  293 inches with two sets of traps
>
> Details:
> Elements are mounted on rectangular aluminum plates, these are attached
> to the boom with U-bolts.  Element sections taper out from the boom.
> Each section is attached by slit tubing and a clamp.  The clamps are
> galvanized steel sheet metal with the clamp nut secured by a small tab
> of the clamp.  The clamp screws are perpendicular to the element.
>
> The traps have covers that appear to be fiberglass with plastic end caps
> (disintegrating in the environment).  The trap cover has a small weep
> hole in it.  The trap coil is bare aluminum wire secured to the
> fiberglass insulator at each end with a screw.  The wire is covered and
> held in place with a thick black paint.  The 10M trap is 10 turns space
> wound 1 wire diameter apart.  The 15M trap is 16 turns.  The reflector
> has only the 15M trap.
>
> The driven element is a dipole with a phenolic center insulator.  This
> is clamped to the boom adaptor plate with a couple of U-bolts.  I have
> not had a chance to check the performance of the balun yet.
>
> If anybody knows what this antenna might be, and where to get a manual,
> please let me know.  I will try to get some pictures up tomorrow to help
> out.
>
> 73, Erich
> N6FD
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1191 / Virus Database: 1435/3385 - Release Date: 01/16/11
>
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk at contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk