[TowerTalk] Prosistel PST61 question

[Andy GD0TEP]

WOW, lots of great advice there, thanks for everything. J

 

The old style PST61 as on Rogers site 'looks' very like my old PST51 that
was on another tower. These rotators are quite good, but weather issues do
seem to be an issue. My 51 is on the bench with the motor stripped for
repair due to water ingress.

 

Looks like I'll be stripping the 61 which will be somewhat easier now that
I've seen a few pictures. thanks very much!

 

I have some info from prosistel who say I should drill out the M8 and fit
M10 bolts. I think I'll rip it apart first and see how it all sits on the
bench.

 

73,

Andy

http://gd0tep.com

 

From: towertalk-bounces at contesting.com
[mailto:towertalk-bounces at contesting.com] On Behalf Of Rroger (K8RI on
TowerTalk)
Sent: 28 January 2011 03:18
To: towertalk at contesting.com
Subject: Re: [TowerTalk] Prosistel PST61 question

 

On 1/27/2011 8:55 PM, Andy GD0TEP wrote:
> Hi to the group,
>
>
>
> My PST61 recently failed. It appears that the mighty large rotator has
what
> IMHO is a inherent weakness, this being the way the rotator is bolted to
the
> bottom mounting casting. Mine is only a couple of years old but has had
> little use, but the four M8 machine screws that hold the two halves of the
> assembly have sheared off. As a picture is 1,000 words, have a look here:
> http://gd0tep.com/rotator/pst61.htm
>
>
>
> I was wondering if anyone on here has ever taken one of these rotators
apart
> before? I'm currently trying to acquire information on how to dismantle
the
> rotator from Prosistel in Italy, but so far, no joy.

Rebuilding the old style PST-61  http://www.rogerhalstead.com/Gears.htm
Looking at the photos should tell you if this PST-61 is close to being
like yours.

They may have some differences but so far I've been told the new and old
housing are similar.
Externally that PST-61 sure looks different than the one I took apart. 
On the link above photos 25 through 30 give a good look at the side of
the PST-61 showing the bottom casting bolted to the body.  I believe it
uses 9 M6 Allen Cap screws.  The only 4 bolt holes are on the top of
mine. The base is part of a casting that bolts to the body.  The seals
and bearings should be available at most automotive stores although you
might have to settle for a single lip instead of double. OTOH I don't
know what you have available there.

The new ones have a DC motor that is longer and smaller in diameter than
the AC motor. The few with the DC motor I've seen were very much like
the one shown being repaired.  The AC motor and be mounted vertically or
horizontally (left or right). You'll note I used white Lithium grease
instead of the original gear lube. I understand they have gone to using
the grease instead of gear lube.

"It appears" that the top plate which does have the 4 M8 bolt holes
(Photo 19) has been used as the bottom plate with a casting mounted to
it, replacing one piece with two.  If that is what happened you *might*
be able to replace the two pieces with the one...IF it will fit the body
of yours.

> It's a little worrying that such a mighty rotator relies on four M8
screws,
> and as each half of the castings have no castellations or other such
> fixings, the 4 screws have to take ALL of the rotator torque.
It appears the screws may not have been torqued down, or were soft.  A
grade 5 M8 can hold a lot of force in the shear mode.  OTOH the ones
I've seen with the one part base all use 9 M6 SS Allen Cap screws.  Then
again it's possible they sell/sold a slightly different model over here.

The positive side is you are a lot closer to France than I am.  I found,
getting parts from the factory took a very long time and that big brass
worm gear wheel is expensive. (Photo 16)
> Anyone with some info to hand?
If I can be of help let me know.

73

Roger (K8RI)
>
>
> 73,
>
> Andy
>
> http://gd0tep.com
>
>
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk


_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk at contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk 

  _____  

No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1204 / Virus Database: 1435/3406 - Release Date: 01/27/11