[TowerTalk] Pull Rope in Conduits?

[Adam Shirley WJ4X]

When you pull the run in, it will spin in the pipe during the pull due
to being coiled up on the reels unless you unroll and straighten the
entire run before the pull (which is impractical in the real world, but
not necessarily the ham world.) OR you've purchased one reel to make a
multi-drop run and have to do it that way.

 73!
 -Adam





On 10/24/2011 6:25 PM, Pete Raymond wrote:
> If the pvc is the correct size for the amount of cable allowing for
> additional cables and the cable to be pulled is properly bundled that
> will not happen.  The pull rope sits outside the bundle.  This method
> has been successfully used for years.  Blowing a new run is difficult
> when your run is not straight.  The key is "when properly done"
> 73 Pete N4KW
> 
> 
> ----- Original Message ----- From: "Adam Shirley WJ4X" <wj4x at amsat.org>
> To: <towertalk at contesting.com>
> Sent: Monday, October 24, 2011 6:04 PM
> Subject: Re: [TowerTalk] Pull Rope in Conduits?
> 
> 
>> The problem with that is the pullstring gets tangled in your cabling
>> when you pull... It's best to blow in a new line for each new pull.
>>
>> 73!
>> -Adam
>>  WJ4X
>>
>> On 10/24/2011 5:58 PM, Pete Raymond wrote:
>>> Think about pulling another pull rope in with the wires.  Then if you
>>> should
>>> ever need to add a wire there will be a pull rope available to pull
>>> the new
>>> wire through.  Do that every time you pull a new cable through.  Good
>>> luck.
>>> 73 Pete N4KW
>>>
>>> ----- Original Message ----- From: "john at kk9a.com" <kk9a at bellsouth.net>
>>> To: <towertalk at contesting.com>
>>> Cc: <n6sj at earthlink.net>
>>> Sent: Monday, October 24, 2011 1:16 PM
>>> Subject: Re: [TowerTalk] Pull Rope in Conduits?
>>>
>>>
>>>> I push #14 electrical wire though while I'm gluing the sections
>>>> together
>>>> and use that to pull the permanent wires once it's buried.  The glue
>>>> on the
>>>> end of the wire has not been an issue.
>>>>
>>>> John KK9A
>>>>
>>>>
>>>>
>>>>
>>>> To:  <towertalk at contesting.com>
>>>> Subject:  [TowerTalk] Pull Rope in Conduits?
>>>> From:  "Steve Jones" <n6sj at earthlink.net>
>>>> Date:  Mon, 24 Oct 2011 08:51:04 -0700
>>>>
>>>>
>>>> I'm about to place a number of 150' Sched 40 PVC conduits between my
>>>> shack
>>>> and new tower.   I want to end up with small 200 lb. stength nylon
>>>> twine
>>>> in
>>>> each conduit, then use that small twine to pull through a larger 1/4"
>>>> nylon
>>>> rope for the actual cable pulls.
>>>>
>>>> Should I use a fish tape to pull through the small twine as I glue
>>>> on each
>>>> additional section of conduit?  I'm concerned about the PVC cement
>>>> sticking
>>>> to the nylon twine.  Or is there an easy way to install the small twine
>>>> after a whole 150' run of conduit is completely glued together?
>>>>
>>>> 73,
>>>>
>>>> Steve
>>>> N6SJ
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> TowerTalk mailing list
>>>> TowerTalk at contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk at contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk at contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk 
> 
>