[TowerTalk] ROHN TOWER BOLTS

[Tom Nicholson]

Just my 2 pennies here, but I'm going to be using SS hardware but I'll 
be using SS Nyloc Nuts. Also if using SS, be sure to use never seize 
compound, if you don't, the nuts will almost for sure seize up if you 
try to remove at a latter date. Lesson "hard learned" with SS bumper 
bolts on my Hot Rod!!!

Tom W1ALZ




On 5/7/2014 9:50 AM, Mark Pride via TowerTalk wrote:
> Heard a story many years ago about a tower that was installed in KH6 with stainless steel hardware and after time, with the constant trade winds, the nuts all fell off.
>    
> There is vibration to contend with in certain places around the world.
>
> Regards,
> Mark, K1RX
>   
>
> On Wednesday, May 7, 2014 9:44 AM, Mark Pride via TowerTalk <towertalk at contesting.com> wrote:
>    
> One other point on the tower hardware from Rohn these days.  They have changed their hardware where the nuts are designed to be put on the bolt ONE time.  To remove the nut, one will damage the thread of the bolt (sorry - forgot the description of this design - lock nut?).  Guess the concept is, you put up a tower one time and never take it down!  However to their point, it prevents nuts from backing off (good thing).
>
> Regarding the new hardware you find in the tower leg of the new material - you might want to change it.  The current nut design has 3 indentations on the surface - pretty easy to spot. Bolts are fine, just need to change the nuts.
>
> Regards,
> Mark, K1RX
>   
>
> On Wednesday, May 7, 2014 7:43 AM, Mike Ryan <mryan001 at tampabay.rr.com> wrote:
>    
> Larry is correct in that both the 25 and 45 use different size bolts and if
> my memory serves me, this would be 4 different sizes in the case of these
> two tower types. I have never seen washers used with these. It is
> noteworthy, that should you be putting tower sections up, to be ABSOLUTELY
> sure that the legs are clear inside. Run a garden hose through the leg to be
> sure there is no blockage, or even push a ground rod through each one for
> example. I can't tell you how many times I have found blockage in the
> legs...dirt, mud, bugs, etc. And while on the subject, occasionally found
> that the blockage was TOWER BOLTS that were packed in the legs by the
> manufacturer which had never been found/removed. -Mike
>
> -----Original Message-----
> From: Larry
> Sent: Wednesday, May 07, 2014 5:47 AM
> To: towertalk at contesting.com
> Subject: Re: [TowerTalk] ROHN TOWER BOLTS
>
> 25G and 45G use two different sizes at each joint on each leg. I forget what
> size they are offhand. DX Engineering sells leg bolts and their web site may
> tell you what the sizes are or the perhaps the Rohn web site.
>
> 73, Larry  W6NWS
>
> -----Original Message-----
> From: Cal Zethmayr
> Sent: Wednesday, May 07, 2014 12:02 AM
> To: towertalk at contesting.com
> Subject: [TowerTalk] ROHN TOWER BOLTS
>
> There is quite a debate at one of our local Saturday morning breakfasts
> gabfests about Rohn Tower Bolts.
>
> Some say that Rohn uses two different size bolt sets for each tower section.
> Some say that Rohn uses only one size bolt-washer-nut sets for all towers.
>
> So what are the facts?
>
> Are there different size bolt sets for Rohn towers, and are they different
> depending on the tower ?  25G, 45G and 55G?
>
> Cal Z
> W4GMH in Crestview, FL.
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>