[TowerTalk] Very old DX Engineering Stack match info wanted

Wayne Kline w3ea at hotmail.com
Tue Nov 15 20:52:15 EST 2016


Hi Mike


   The boxes your talking about are the "OLD  DXEngineering "

I had three of the stack boxes and one 4 sq box for 80 meters.

There  gone ( lightning HIT )   But I do have a instruction manual.


  DX Engineering inc.

  18 Spalding ave  Brownsville Oregon


It's called  0 Phase Box

The   1/4 wave phasing lines at made from good quality RG-11  ( 75 ohm coax)  ( 246/ Freq. in MHZ  X velocity factor of line = line length   )


 Upper Yagi  Port #1

 Lower Yagi Port #2


 Phase line  Port # 3 to # 5        Port  #4 to # 6  ( 75 ohm phase line )


Port #7  input


Wayne  W3EA


________________________________
From: TowerTalk <towertalk-bounces at contesting.com> on behalf of Mike Smith VE9AA <ve9aa at nbnet.nb.ca>
Sent: Tuesday, November 15, 2016 9:55 AM
To: towertalk at contesting.com
Subject: [TowerTalk] Very old DX Engineering Stack match info wanted

I have a very old DX Engineering Yagi Stacking control box I am trying to
find some info on.  I think it's late 80's/early 90's vintage.

I believe it was acquired from a W7 6m Dxer friend back in the mid 90's.
(but it was already somewhat old then).  I don't know the history of DX
Engineering, but did it once reside on the west coast by different folks>?



The grey faced, black cabinet control box has a rotary switch for settings
UPPER/LOWER/STACK (with matching LED's) and a simple on/off toggle.

I am nearly certain it uses only 3 wires for control, though the terminal
strip has more than 3 connections.



I used it on my 6m stack before I moved to my current location in 2004, so I
don't recall what's needed at the tower end for phasing/matching coax
cables.

Ie: Is it 50Ohm? 75Ohm? 1/2wl? 1/4wl?  Which connections?  I have to redo
the remote part as I took it out of service due to a faulty relay or
connections, best as I recall (Hey, I don't throw much away, hi)



IIRC I might have had another remote switch to put them both out of phase,
but don't know where that is.  I don't see anything in the box to be able to
do that, so I presume I did it with an external remote switch added to this
to perform that function. (as an aside, I seldom used BOP..wouldn't waste my
time if I ever stack 2m 6m yagis again, hi!)



***Anyways, my intention is to now reuse this to perhaps phase 2 verticals
for a BS/EF or 2 other directions array.



I was thinking 2 x 1/4WL verticals, spaced 1/2wl apart, with a parasitic
reflector between them, giving me (perhaps_ NE, SW and one other dual
direction pattern , depending on what I can do with a phasing line.



Haven't decided on the band yet..maybe 10m or one of the WARC bands.



TNX,



Mike VE9AA







Mike, Coreen & Corey

Keswick Ridge, NB



_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk at contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

TowerTalk Info Page - Contesting<http://lists.contesting.com/mailman/listinfo/towertalk>
lists.contesting.com
TowerTalk is for discussion of tower and HF antenna construction topics. TT members have lots of helpful information and are happy to share it.





More information about the TowerTalk mailing list