[TowerTalk] 39 +j0 ohms?

[Jamie WW3S]

I'm preparing for the 2 ELE DXE array.....and now, with just about 3 ft of 
coax, at the target freq of 7.125 mc, #1 vert measures Z=41.1, R=40.8 and 
X=.93  and #2 measures Z=40.8, R=40.6 and X = 3.2. I then attached the 75 
ohm 1/4 wave stubs, and the Tee adapter, and measure right at the Tee and 
got Z=51.2,  R=48.3 and X=14.4...the instructions say it should read close 
to  46 ohms +j 12 ohms.....so am I close? I'm stuck on what the j+12 ohms 
means in relation to the other readings....

-----Original Message----- 
From: Tim Duffy
Sent: Sunday, December 02, 2018 4:11 PM
To: 'Wes N7WS' ; jim at audiosystemsgroup.com
Cc: towertalk at contesting.com
Subject: Re: [TowerTalk] 39 +j0 ohms?

Jamie:

Is this a full size vertical (1/4 wavelength) with a proper radial field?

If the VSWR is 1.3:1 at 7125 KHz - what is the problem you are trying to
solve? What frequency is X=0?

73,
Tim K3LR

-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces at contesting.com] On Behalf Of Wes
N7WS
Sent: Sunday, December 02, 2018 4:05 PM
To: jim at audiosystemsgroup.com
Cc: towertalk at contesting.com
Subject: Re: [TowerTalk] 39 +j0 ohms?

No, you just need to calibrate at the far end of the coax.

Sent from my iPhone

> On Dec 2, 2018, at 1:27 PM, Jim Brown <jim at audiosystemsgroup.com> wrote:
>
> Where are you measuring?  You'll only get the actual impedance measuring
right at the feedpoint with a very short piece of coax connecting the
analyzer.
>
> Now, it IS possible to transform a measurement made at the end of a long
piece of coax to the feedpoint Z, but to do that you need to save the data
to a file and export to software like AC6LA's ZPlots or AE6TY's SimSmith.
AND you need to know the length of the feedline, know the exact type of
coax, and plug both into the software.
>
> 73, Jim K9YC
>
>> On 12/2/2018 12:07 PM, Jamie WW3S wrote:
>> trying to understand a 40m vertical, my Rigexpert analyzer has Z, X, R
and C.......when I measure the vertical at 7.125 (target freq) the SWR is
1.3:1, but the Z is 50 ohms, I'm told the impedance needs to be 39+j) ohms?
How can I read that with my rigexpert.....I can get around 39 ohms at
7.400.....is my vertical too long, or too short?
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk at contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk at contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk at contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk at contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

---
This email has been checked for viruses by AVG.
https://www.avg.com