[VHFcontesting] stacked yagi's

[Paul Kiesel]

Thank you, Jim! Of course, you are right. Multiples of a quarter wavelength is what I should have said in my message. Thanks again, Jim.

73,
Paul




________________________________
From: Jim Forsyth <mail at jimforsyth.com>
To: Paul Kiesel <k7cw at yahoo.com>
Sent: Mon, April 12, 2010 9:25:23 AM
Subject: Re: [VHFcontesting] stacked yagi's

Paul,

I don't think half wavelengths are going to do it, that will just reproduce 
the impedance present at the other end. You want odd multiples of quarter 
wavelength.

Jim, AF6O

--------------------------------------------------
From: "Paul Kiesel" <k7cw at yahoo.com>
Sent: Sunday, April 11, 2010 10:56 AM
To: <vhfcontesting at contesting.com>
Subject: Re: [VHFcontesting] stacked yagi's

> If you use a power divider, use two equal lengths (it doesn't matter how 
> long they are) of 50 ohm coax, from the power divider ports to each yagi. 
> The impedance transformation is going on in the power divider, so  you 
> already have 50 ohms available at each of the power divider's ports.
>
> If you elect to use coax, use 75 ohm coax so you get the proper impedance 
> transformation. You must use exact multiples of an electrical half 
> wavelength. You will want to use as little coax as possible to reduce your 
> losses in the coax, so if you elect to make both lengths of coax an EVEN 
> number of half wavelengths long, then you will orient the feeds of the 
> antennas so that they are both on the same side, symmetrical with each 
> other, if you will. But, if you decide to have one length of coax be an 
> EVEN number of half wavelengths long and the other length of coax an ODD 
> number of half wavelengths long, then you will need to reverse the feed on 
> the second yagi so that it is reverse from the first yagi. This is because 
> the extra half wavelength of coax that you have going to one of the yagis 
> will result in a 180 degree shift in phase. So, in order to get both 
> antennas in phase with each other, you will need to reverse the feed on 
> one of them by flipping the
> antenna upside-down or by mechanically re-arranging the feed.
>
> 73,
> Paul, K7CW
>
>
>
>
> ________________________________
> From: Jon Casamajor <k6el at comcast.net>
> To: vhfcontesting at contesting.com
> Sent: Sat, April 10, 2010 2:09:05 PM
> Subject: Re: [VHFcontesting] stacked yagi's
>
> Hi Paul,
>
> I am a little confused on what you are doing I guess.   I have two M²
> 420-50-11 Yagis stacked vertically, that is one above the other.  I am 
> using
> a standard M² splitter and stacking harness and the distance between the
> Yagis is 28” and the phasing lines are identical in length however I’m not
> entirely sure of their length as they are living at about 100’ now.  J
>
> You said… “(note that I might switch units without warning)”, so I may not
> be seeing something here.  If both phasing lines are the same length
> wouldn’t they be fed in phase?  My little stack is on my QRZ page in case
> I’ve confused you in return.  The little stack works quite well but I’m
> planning to replace it soon with a 4329WL as the stack is a little sharp 
> and
> I need a bit more ERP.
>
>
>
>
>
> 73, Jon
>
> K6EL
>
> -----Original Message-----
>
>
>
>
>
> ------------------------------
>
>
>
> Message: 2
>
> Date: Sat, 10 Apr 2010 03:07:25 +0000 (UTC)
>
> From: Paul Decker <kg7hf at comcast.net>
>
> Subject: [VHFcontesting] stacked yagi's
>
> To: vhfcontesting at contesting.com
>
> Message-ID:
>
>
> <1210296233.8429611270868845217.JavaMail.root at sz0009a.westchester.pa.mail.co
> mcast.net>
>
>
>
> Content-Type: text/plain; charset=utf-8
>
>
>
>
>
>
>
> Hey group,
>
>
>
>
>
>
>
> I'm in the process of stacking two 11 element 70cm yagi's.? I've modeled 
> it
> in eznec and I think the optimum distance is about 42".? (note that I 
> might
> switch units without warning).
>
>
>
>
>
>
>
> Once I have the two 50 yagi's stacked, my model says I need to have one 
> 180
> out of phase, does this seem right?
>
>
>
>
>
>
>
> If that is the case, then I need different lengths of coax to feed each
> antenna.
>
>
>
>
>
>
>
> Should I use a 50 ohm power divider and feed each antenna with 1.25w and
> 1.75w 50 coax, or should I feed with 1.25 and 1.75 75 Ohm coax and simply
> use a T connecter.? Is there an advantage of one over the other?
>
>
>
>
>
>
>
> thanks for any help, 73,
>
>
>
> Paul (KG7HF)
>
>
>
>
>
> ------------------------------
>
>
>
> _______________________________________________
>
> VHFcontesting mailing list
>
> VHFcontesting at contesting.com
>
> http://lists.contesting.com/mailman/listinfo/vhfcontesting
>
>
>
>
>
> End of VHFcontesting Digest, Vol 88, Issue 9
>
> ********************************************
>
> _______________________________________________
> VHFcontesting mailing list
> VHFcontesting at contesting.com
> http://lists.contesting.com/mailman/listinfo/vhfcontesting
>
>
>
>
> _______________________________________________
> VHFcontesting mailing list
> VHFcontesting at contesting.com
> http://lists.contesting.com/mailman/listinfo/vhfcontesting
>