[WriteLog] 5NN instead of 599

[Tim-M0BEW]

Use %N3 for run exchanges (cut numbers).

Use %3 for s&p exchanges and number repeats (non-cut numbers).

Tim M0BEW.


----- Original Message ----- 
From: "Mel" <ve2dc at rac.ca>
To: "'George Johnson'" <w1zt at comcast.net>; "'Al Zelna'"
<mr.mri at evenlink.com>; "'Joe Young'" <jwyoung at cybertrails.com>;
<writelog at contesting.com>
Sent: Monday, May 31, 2004 11:18 AM
Subject: RE: [WriteLog] 5NN instead of 599


> Is there a way to override the cut number variable. I was using T and N
but
> would prefer to NOT use them when sending a repeat for the number...
>
> > -----Original Message-----
> > From: writelog-bounces at contesting.com
> > [mailto:writelog-bounces at contesting.com] On Behalf Of George Johnson
> > Sent: May 31, 2004 05:42
> > To: Al Zelna; 'Joe Young'; writelog at contesting.com
> > Subject: RE: [WriteLog] 5NN instead of 599
> >
> >
> > Al,
> > No.  The Cut-Numbers section only applies to transmitted CW.  And it
> > applies to the "sequence number" but I have not checked it
> > for things like
> > "time".   I need to check it for WAE because I think I recall
> > cut numbers
> > in the QTC exchanges for WAE CW.  All other buffer contents
> > that might
> > numbers for RTTY come out as the correct numbers.
> > 73, George .. W1ZT
> >
> >
> > At 10:16 PM 5/30/2004, Al Zelna wrote:
> > >Sounds real nice... and I wish I checked my email before WPX started
> > >hihi.
> > >
> > >One question:  Does adding this section to the WL .ini file
> > affect how
> > >the numbers are transmitted using RTTY?
> > >
> > >Al, N3KAE
> > >
> > >
> > >
> > >-----Original Message-----
> > >From: writelog-bounces at contesting.com
> > >[mailto:writelog-bounces at contesting.com] On Behalf Of George Johnson
> > >Sent: Saturday, May 29, 2004 08:51 AM
> > >To: Joe Young; writelog at contesting.com
> > >Subject: Re: [WriteLog] 5NN instead of 599
> > >
> > >Joe,
> > >Add a section to your Writelog.ini file:
> > >
> > >[Cut-Numbers]
> > >0=T
> > >9=N
> > >1=A
> > >
> > >etc.
> > >73, George .. W1ZT
> > >
> > >At 08:37 AM 5/29/2004, Joe Young wrote:
> > > >Hello,
> > > >I have asked this one before but due to hard drive failure and
> > > >subsequent replacement I need to ask again.
> > > >
> > > >In Writelog how do I change the keying characteristics to have:
> > > >
> > > >9 = N
> > > >0 = T
> > > >1 = A
> > > >
> > > >etc.
> > > >
> > > >Thanks and 73 de Joe, W6RLL
> > > >
> > > >
> > > >
> > > >_______________________________________________
> > > >WriteLog mailing list
> > > >WriteLog at contesting.com
> > > >http://lists.contesting.com/mailman/listinfo/writelog
> > > >WriteLog on the web:  http://www.writelog.com/
> > >
> > >
> > >_______________________________________________
> > >WriteLog mailing list
> > >WriteLog at contesting.com
> > >http://lists.contesting.com/mailman/listinfo/writelog
> > >WriteLog on the web:  http://www.writelog.com/
> >
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog at contesting.com
> > http://lists.contesting.com/mailman/listinfo/w> ritelog
> >
> > WriteLog on the web:  http://www.writelog.com/
> >
>
> _______________________________________________
> WriteLog mailing list
> WriteLog at contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/
>
>