[WriteLog] writelog via kam standard tnc in clone mode
ve2lx at sympatico.ca
Wed Dec 19 11:43:38 EST 2007
Thank you so much for replying so rapidely
Kam stdr is in fact what you ment...the KAM basic model before the kam 98 or
Ok for the answer but
I am almost shure I seen ((( in the KAM98 ))) manual that there is a command
in command mode to remove it or reduce the length of the during time in
milli seconds...but I did not find it again and I am making research about
Friend of mine will bring me the manual of the KAM for search.
With WL and MMTTY or MMTTY alone (there is in fact that tone) but much
shorter so no time lost in contests.
Your hel was really appreciated
Best wishes for Xmas
----- Original Message -----
From: "Robert Chudek - K0RC" <k0rc at pclink.com>
To: "ve2lx" <ve2lx at sympatico.ca>; "witelog group" <writelog at contesting.com>
Sent: Wednesday, December 19, 2007 1:34 AM
Subject: Re: [WriteLog] writelog via kam standard tnc in clone mode
I do not know what a "Kam stdr" is.
In the Kantronics KAM and KAM Plus, this startup delay is built into the
firmware and is not adjustable. I had a discussion with Kantronics about
this when the KAM was first introduced. They choose not to change it because
the engineers felt it was necessary to give the receiving end some time to
synch up before starting to decode data.
The HAL, AEA, and MFJ TNC's did not have this hard-coded limitation.
73 de Bob - KØRC in MN
----- Original Message -----
From: "ve2lx" <ve2lx at sympatico.ca>
To: "witelog group" <writelog at contesting.com>
Sent: Wednesday, December 19, 2007 12:13 AM
Subject: [WriteLog] writelog via kam standard tnc in clone mode
> Hello to all
> best wishes for christmas and new year
> I added a TNC kam stdr to my pro3 recently for RTTY contests.
> I was using writelog + mmtty but again decided to work with two different
> flat screens configuration.
> Kam stdr as main and WL + MMTTY on clone in RTTYrite.
> But there is a thing I do not like with WL transmit across the TNC...it
> put a steady tone (mark) (before) to start to TX (diddling the texte
> transmission after).
> Wtih WL and MMTTY that tone is but much shorter and almost not eared
> (being so short)
> In contests it is a time lost.
> Can we reduce the time delay of (that TNC tone) in WL.ini file for he Kam
> TNC operation...?
> Or can we remove it by WL.ini...?
> To compare using WL and MMTTY that tone is shorter.
> With MMTTY alone it is also shorter and same delay.
> During the last rtty contest while listening other stations, I eared only
> few stations with a long mark tone like that before the rtty texte is
> sent, probably mean the use a TNC?
> Can someone help me...
> Using two screens with a TNC and WL + MMTTY clone window (2 different
> units demodulating the same signal and texte sent) is very often helpfull
> to see calls end letters errors particulary in contests where speed is
> If I can not ameliorate that situation i'll reconnect WL + MMTTY +
> rigbalster direct to the radio ACC 1 connector and then feed RADIO AUDIO
> to TNC AND to COMPUTER PORT...but I would really prefer to save that work
> and connect as it is now KAM main and WL - MMTTY in clone qindow saving me
> to modify physical connections
> Gilles VE2LX
> ve2lx at sympatico.ca
> WriteLog mailing list
> WriteLog at contesting.com
> WriteLog on the web: http://www.writelog.com/
WriteLog mailing list
WriteLog at contesting.com
WriteLog on the web: http://www.writelog.com/
More information about the WriteLog