[WriteLog] Using MMTTY with WriteLog

[Don Hill AA5AU]

This is incorrect.

Software generated FSK will work for USB-to-serial adapters with the MMTTY plug-in.  I'm doing it on one computer/radio now.  The
key is to go to MMTTY stand-alone and change EXTFSK to the port number of the adapter on the TX tab and then on the MISC tab, USB
Port, select C: Limiting Speed.  In WL, select the port of the adapter in the Rttyrite menu along with Software generated FSK.

Rick's having a similar issue but the suggestions we have been giving him aren't working for some reason. 


73, Don AA5AU
http://www.aa5au.com
http://www.rttycontesting.com 

-----Original Message-----
From: writelog-bounces at contesting.com [mailto:writelog-bounces at contesting.com] On Behalf Of Joe Subich, W4TV
Sent: Sunday, March 02, 2008 8:53 PM
To: 'Rick Lindquist'; writelog at contesting.com
Subject: Re: [WriteLog] Using MMTTY with WriteLog


If your USB to serial adapter does not support 5bit codes at 45.45 baud (e.g., if you must use EXTFSK for MMTTY in stand alone
mode), the MMTTY plug-in will not work. 

The MMTTY plug-is does not permit the use of EXTFSK and WriteLog's "Software generated FSK (TxD)" is only valid for RTTYrite (the
native RTTY support with Sound Board FSK or Stereo Sound Board FSK).  

73, 

   ... Joe, W4TV 
 



> -----Original Message-----
> From: writelog-bounces at contesting.com 
> [mailto:writelog-bounces at contesting.com] On Behalf Of Rick Lindquist
> Sent: Saturday, March 01, 2008 7:21 PM
> To: writelog at contesting.com
> Subject: [WriteLog] Using MMTTY with WriteLog
> 
> 
> Well, I'm stumped again. Even after reviewing (and reviewing) the fine 
> tutorials by Don, AA5AU, I still cannot get the MMTTY module to 
> transmit FSK RTTY with WriteLog. MMTTY works fine as a standalone 
> program from its currently assigned COM port (7), and I can even get 
> Rittyrite to transmit FSK (from the type-ahead buffer; there don't 
> appear to be any memories - just a funky little tuning screen with a 
> very slow response time).
> 
>  
> 
> After selecting the COM 7 under Rittyrite's Ports menu, then "Software 
> generated FSK TXD," the "COM-TxD(FSK)" choice in the MMTTY Setup MISC 
> screen is grayed out. At one point, I got MMTTY/WriteLog to key the 
> radio, but it just transmitted a carrier, not RTTY.
> 
>  
> 
> I'm using a RIGblaster Plus on COM 7 via a USB - >RS-232 
> adapter. The radio
> is an ICOM IC-756PROIII. I had been using the general DXCC 
> tracker logging
> module, but it still would not work after I loaded an RTTY 
> RoundUp contest
> module.
> 
>  
> 
> Any ideas or suggestions? Many thanks! 73, Rick, N1RL
> 
> _______________________________________________
> WriteLog mailing list
> WriteLog at contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/

_______________________________________________
WriteLog mailing list
WriteLog at contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/