[WriteLog] FTDX 5K and MicroHam DXP

[Joe Subich, W4TV]

> Thing is are you familiar with Writelog's  Digirite program.
I am not familiar with Digirite - have never looked at it.

> I somehow think my problem is a menue setting with MicroHam DXP.
There are no menu settings in DXP that affect the sound card.

*ANY* sound card software should be configured to use "Line (DXP)"
- Left channel for transmit and DXP RX (DXP) - left channel for
receive (on the main receiver).  If you have a dual receiver rig
and the software supports dual receive, the second receive channel
should be configured for the rig's second/sub RX as DXP RX (DXP)
- *right* channel.

Receive audio level should be adjusted *separately* with the encoder
for the main (left) and sub (right) channels.  "DXP RX" has *NO*
Windows mixer component so receive level does not respond to any
"slider" in the application or Windows driver/Sound Control Panel.

> When I activate Digirite view from inside Writelog it reports
> "failed to open wave input"  could that be because of a DXP menue
> choice?

Again, there is  no sound card menu choice in DXP.  The error message
you quote would almost certainly indicate a configuration error in
WriteLog/Digirite or that you have disabled application access to the
"microphone" (any audio input) in Windows -> Privacy & Security ->
Microphone.

I *DO NOT HAVE* the current version of Writelog *and* have never
built/installed Digirite.  I can not help you there.

73,

    ... Joe, W4TV


On 8/25/2023 3:11 PM, robert beaudoin wrote:
> 
>          Good Afternoon Joe
> 
>                  I hate to be a pest but......   your previous response 
> really got me going with
> 
>                  Writelog and  MicroHam DXP.   Thanks again ...... Thing 
> is are you familiar
> 
>                  with Writelog's  Digirite program.    I somehow think 
> my problem is a menue
> 
>                  setting with MicroHam DXP.   I can not get Digirite to 
> work with Writelog
> 
>                      I used to enjoy that program when I was able to use 
> a  MicroHam Digikeyer 2.
> 
>                  Digirite ask for sound info.    When I activate 
> Digirite view from inside Writelog
> 
>                  it reports  "failed to open wave input"  could that be 
> because of a DXP menue
> 
>                  choice?    Information on the web seems to pertain to 
> OLD ver. of Writelog?
> 
>                  I am down to my last day to figure this out as I was 
> hoping to enter World Wide Digi
> 
>                  test tomorrow.
> 
>                          In any cas Joe  all the best     73   BoB WA1FCN
> 
> 
> 
> On 8/24/2023 8:21 PM, Joe Subich, W4TV wrote:
>>
>> In DXP Setup Set 1.2 "CAT DTR" = None
>> By default, WriteLog asserts DTR on the CAT port for most current
>> Kenwood and Yaesu rigs.
>>
>> 73,
>>
>>     ... Joe, W4TV
>>
>>
>>> On 8/24/2023 8:11 PM, robert beaudoin wrote:
>>>>
>>>>          Good Evening All
>>>>
>>>>              Anyone using Writelog and MicroHam DXP   FTDX 5K ?
>>>>
>>>>                  Every time I try to load Writelog PTT comes on and 
>>>> I can not stop it.  I uninstalled
>>>>
>>>>                      Writelog and then re-installed it same thing? I 
>>>> just started learning this DXP a few
>>>>
>>>>               days ago so far I like Microham Digi Keyer Router 
>>>> menue better.....   I got frequency read out
>>>>
>>>>                  OK..   MMTY is  fine  and WSJT is fine...... I 
>>>> really wanted to use Writelog with Digirite
>>>>
>>>>                       in World Wide Digi  test.  I believe I can use 
>>>> WSJT in contest mode?
>>>>
>>>>                              Ok thanks for any leads...... 73 BoB 
>>>> WA1FCN
>>>>
>>>>