A very simple fix, which worked for years with my SB-220 and TS-930, is to
insert a 220-ohm resistor in series with the kPTT lead. Does nothing for
the voltage rating of the transceiver switching circuit, but it does limit
the current surges that weld relay contacts together.
73, Pete N4ZR
At 10:20 AM 11/9/2008, W4TV wrote:
>The keying line (PTT relay) in the SB-220 is +120 V DC. The contacts
>of the "Linear" or "Send" relays in most transceivers can not handle
>the voltage and current "spike" generated by the high voltage PTT
>circuits in the older amplifiers (SB-200, SB-220, L4, L7, TL-922, etc.).
>You will probably need to replace the "Linear" or "Send" relay in your
>transceiver (if you are lucky, that will be all).
>
>I suggest adding a keying buffer (e.g. Ameritron ARB-704), modifying
>the SB-200 with the internal Harbach Electronics soft key circuit
>(www.harbachelectronics.com/main/page_products_sb220__sb221.html),
>or converting the SB-200 to faster, low voltage relays and electronic
>bias switching.
>
>73,
>
> ... Joe, W4TV
>
>
>
> > -----Original Message-----
> > From: amps-bounces@contesting.com
> > [mailto:amps-bounces@contesting.com] On Behalf Of Roger (K8RI)
> > Sent: Sunday, November 09, 2008 12:34 AM
> > To: ke1fo@arrl.net
> > Cc: amps@contesting.com
> > Subject: Re: [Amps] SB-220 saga continues
> >
> >
> > Please do not cross post between reflectors.
> >
> > Roger (K8RI)
> >
> > Alfred Frugoli wrote:
> > > Hello everyone,
> > >
> > > So it seems I've got a problem with my SB-220.
> > >
> > > When the amp is off, but connected in the RF path,
> > everything is fine.
> > >
> > > When I switch the amp on I've suddenly got lots of attenuation
> > > happening on the receive path. Transmit seems fine - amp tunes OK
> > > etc.
> > >
> > > My first suspicion was that there were dirty relay contacts on the
> > > receive side. Cleaned the contacts with no success. Then
> > I realized
> > > that the problem only occurs when the amp is on. So a trip to the
> > > schematic tells me I don't understand. In the RX mode the RF path
> > > through the amplifier should be the same as when the power
> > is on. So
> > > I'm not sure where my attenuation is coming from.
> > >
> > > Just testing it a few minutes ago I can make an S5-7 station almost
> > > completely disappear by turning on the amp, so I've got
> > somewhere in
> > > the area of 20db of attenuation happening!
> > >
> > > Thoughts?
> > >
> > > Thanks.
> > >
> > > 73 de Al, KE1FO
> > >
> > > -----
> > > Visit my amateur radio contesting blog at ke1fo.wordpress.com.
> > > _______________________________________________
> > > Amps mailing list
> > > Amps@contesting.com
> > http://lists.contesting.com/mailman/listinfo/amps
> > >
> > >
> >
> > _______________________________________________
> > Amps mailing list
> > Amps@contesting.com http://lists.contesting.com/mailman/listinfo/amps
>
>_______________________________________________
>Amps mailing list
>Amps@contesting.com
>http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|