Amps
[Top] [All Lists]

Re: [Amps] snubbing diodes for vac relays / notes.

To: "[Amps]" <amps@contesting.com>
Subject: Re: [Amps] snubbing diodes for vac relays / notes.
From: Pete Smith <n4zr@contesting.com>
Reply-to: n4zr@contesting.com
Date: Thu, 11 Mar 2010 17:32:27 -0500
List-post: <amps@contesting.com">mailto:amps@contesting.com>
Why not just use a high voltage MOSFET to switch the bias, controlled 
with the same voltage that runs the input relay?

73, Pete N4ZR

The World Contest Station Database, updated daily at www.conteststations.com
The Reverse Beacon Network at http://reversebeacon.net, blog at 
reversebeacon.blogspot.com


On 3/11/2010 5:12 PM, Bill VanAlstyne W5WVO wrote:
> Hi Jim,
>
> I was particularly interested in this part of your response:
>
>    
>> In any event, the AUX  contacts on it are only rated for 28 vdc !!    You
>> will destroy
>> them, if  using + 120vdc  for  switching cut off bias.  +120 vdcv  for cut
>> off bias is
>> dinosaur technology.  Better  to simply use a 100 K  3 watt  MOF  in the
>> CT of the
>> fil xfmr.. and short  the same 100 k R  out  with the  contacts   of the
>> bias relay.
>> Only a spst relay is required for this.
>>      
> I discovered the 28VDC rating of the aux contacts AFTER I bought the damned
> thing... D'oh!! The rating may have more to do with total power dissipation
> than with voltage above ground, so it might work anyway... I'm open to
> trying your idea, though, once I understand it.
>
> In the SB-220 (and also I think other similar GG amps from the same era),
> the center-tap (C.T.) of the filament transformer is connected to the common
> pole of the SPDT contacts. In RX mode, the normally-closed contact provides
> the C.T. with cut-off bias (120VDC). In TX mode, the 8+V operating bias is
> connected to the C.T.
>
> Can you be more specific in your recommendation? What are you connecting
> through the 100K ohm resistor to the filament transformer C.T.? The
> operating bias, I would have to think -- with the resistor shorted out in TX
> mode. In RX mode, then, the tube cathodes would get the same operating bias,
> but through the 100K ohm resistor. I'm not quite visualizing how that would
> work in cutting off the tubes. Please explain?
>
> Thanks,
> Bill W5WVO
>
>
>
>
>    
>> On another note.  He is using  2 x vac relays  +  3rd relay... with all
>> their coils in series, plus
>> a  shunting resistor across the bias relay coil.  This will work  with
>> +120 vdc.. and
>> speed all 3 x of em up.
>>
>> On the 2 x GS35B  6m amp,  I  helped a friend with... we used  3 x
>> Gigavac GH-1's
>> [like a rj1a]   one  for input, one for output, 3rd one for the bias [
>> shorts out the 100k R]
>> All of  em have 12 vdc coils. All are very easy to speed up  with an
>> overvoltage.. and just one
>> series  dropping resistor.  If u want to speed  em up even faster, install
>> a 50 uf lytic  across
>> the  dropping resistor. Then u end up with a 'RC  hotshot speed up
>> circuit' .
>>
>> On the 6m amp.. both GH-1's  mounted side by side, with 2 x SO-239's above
>> them.
>> Bypass  swr on 6m is dead flat.
>>
>> For his proposal,  I would deep 6 the idea of using +120 vdc  for cut off
>> bias.. and
>> use the 100k  R  in the CT  of fil xfmr.   We always use 2 x 100 K  in
>> parallel,,, for
>> redundancy.
>>
>> later... Jim   VE7RF
>>
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>>
>>      
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>    
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>